20xxMCM o奖summary 美赛精读内容(3800字)

发表于:2017.5.25来自:www.ttfanwen.com字数:3800 手机看范文

2000MCM- SUMMARY

The Safe Distance Between Airplanes and the Complexity of an Airspace Sector

Finale Doshi

Rebecca Lessem

David Mooney

Governor’s School

Richmond, VA

Advisor: Crista Hamilton

Summary

We determine the minimum safe spacing between aircraft and also the complexity of the air traffic control system.

Taking into account the vortex that a leading plane leaves in its wake, the distance between the tail of one plane and the nose of the next plane should be at least 5.5 km or 3.4 mi. The minimum spacing between adjacent planes either to the side, above, or below should be at least 730 m or 0.45 miles. These distances were calculated using Bernoulli’s principle, which states that the internal pressure of a fluid (such as air) decreases when its speed increases. Because the speed of a plane is very high, the pressure around the wings is low. The change in pressure associated with the Bernoulli factor, applied over the facing surface area, results in a force pushing the planes together; the force may alter the plane’s flight pattern.

Finally, if two planes are heading towards each other, there must be enough space between them to perform evasive maneuvers. We find that 12 s is required; at normal flight speed, this translates to 2.9 km or 1.8 mi.

We define complexity of an airspace sector as the probability of a conflict occurring during a given period of time. To determine complexity, we assume that sectors are rectangular solids and that planes fly either in parallel or antiparallel

directions. We calculate the probability that a plane enters a sector

either too soon after another plane, or that two planes enter the same airway going in antiparallel directions.

TheUMAPJournal 21 (3) (2000) 257–267. c_Copyright 2000 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 258 The UMAP Journal 21.3 (2000)

The weaknesses of this model include that all planes are assumed to be Boeing 767s. This model also does not take into account weather changes and

multiple conflicts.

The strengths of this modeling include allowing for passenger safety while

slightly shortening the Federal Aviation Administration (FAA) minimum distances, thereby increasing airspace capacity. The complexity model accounts

for stress; stability analysis shows that a small change in the environment does not drastically change the model.

Radio Channel Assignments

Justin Goodwin

Dan Johnston

Adam Marcus

Washington University

St. Louis, MO

Advisor: Hiro Mukai

Summary

We use mainly combinatorial methods to estimate and prove bounds for

various cases, concentrating on two levels of interference. We use the concept of a span, the minimum largest channel among assignments that satisfy the constraints.

For Requirements A and B, the span is 9. For Requirement C, the span is 7 when k = 1, 9 when k = 2, 12 when k = 3, and 2k + 7 for k ≥ 4.

For Requirement D, we present the results in a table (Table 2). Some of our results improve on upper bounds in Shepherd [1998].

Only regular transmitter placement needs to be considered; irregular placement can be accommodated by making the hexagons so small that the transmitters are in regular placement, with the bounds adapted correspondingly.

For Requirement E, we discuss both the limitations of our model and its ability to produce an upper bound for any situation.




第二篇:20xxmcm美赛特等奖o奖论文 181000字

The

UMAP

Publisher

COMAP, Inc. Vol. 31, No. 2

Executive Publisher

Solomon A. Garfunkel

ILAP Editor

Chris Arney

Dept. of Math‘l Sciences

U.S. Military Academy

West Point, NY 10996

david.arney@usma.edu

On Jargon Editor

Yves Nievergelt

Dept. of Mathematics

Eastern Washington Univ. Journal

Cheney,WA 99004 ynievergelt@ewu.edu Reviews Editor James M. Cargal Mathematics Dept. Troy University— Montgomery Campus 231 Montgomery St. Montgomery, AL 36104 jmcargal@sprintmail.com Chief Operating Officer Laurie W. Arag?on Production Manager GeorgeWard

Copy Editor

Julia Collins

Distribution

John Tomicek Editor

Paul J. Campbell Beloit College 700 College St.

Beloit, WI 53511–5595 campbell@beloit.edu Associate Editors Don Adolphson Chris Arney

Aaron Archer

Ron Barnes

Arthur Benjamin Robert Bosch James M. Cargal Murray K. Clayton Lisette De Pillis James P. Fink

Solomon A. Garfunkel William B. Gearhart William C. Giauque Richard Haberman Jon Jacobsen Walter Meyer

Yves Nievergelt Michael O‘Leary

Catherine A. Roberts

John S. Robertson

Philip D. Straffin

J.T. Sutcliffe

Brigham Young Univ.

Army Research Office

AT&T Shannon Res. Lab.

U. of Houston—Downtn

Harvey Mudd College

Oberlin College

Troy U.— Montgomery

U. of Wisc.—Madison

Harvey Mudd College

Gettysburg College

COMAP, Inc.

Calif. State U., Fullerton

Brigham Young Univ.

Southern Methodist U.

Harvey Mudd College

Adelphi University

Eastern Washington U.

Towson University

College of the Holy Cross

Georgia Military College

Beloit College

St. Mark‘s School, Dallas

Subscription Rates for 2010 Calendar Year: Volume 31

Institutional Web Memberships do not provide print materials. Web memberships allow

members to search our online catalog, download COMAP print materials, and reproduce them for classroom use.

(Domestic) #3030 $467 (Outside U.S.) #3030 $467

Institutional Memberships receive print copies of The UMAP Journal quarterly, our annual CD collection UMAP Modules, Tools for Teaching, and our organizational newsletter

Consortium.

(Domestic) #3040 $312 (Outside U.S.) #3041 $351

Institutional Plus Memberships receive print copies of the quarterly issues of The UMAP

Journal, our annual CD collection UMAP Modules, Tools for Teaching, our organizational

newsletter Consortium, and online membership that allows members to search our

online catalog, download COMAP print materials, and reproduce them for classroom use.

(Domestic) #3070 $615 (Outside U.S.) #3071 $659

For individual membership options visit

for more information.

To order, send a check or money order to COMAP, or call toll-free 1-800-77-COMAP (1-800-772-6627).

The UMAP Journal is published quarterly by the Consortium for Mathematics and Its

Applications (COMAP), Inc., Suite 3B, 175 Middlesex Tpke., Bedford, MA, 01730, in cooperation

with the American Mathematical Association of Two-Year Colleges

(AMATYC), the Mathematical Association of America (MAA), the National Council of

Teachers of Mathematics (NCTM), the American Statistical Association (ASA), the Society for Industrial and Applied Mathematics (SIAM), and The Institute for Operations Research

and the Management Sciences (INFORMS). The Journal acquaints readers with a wide variety of professional applications of the mathematical sciences and provides a forum

for the discussion of new directions in mathematical education (ISSN 0197-3622). Periodical rate postage paid at Boston, MA and at additional mailing offices. Send address changes to: info@comap.com

COMAP, Inc., Suite 3B, 175 Middlesex Tpke., Bedford, MA, 01730

? Copyright 2010 by COMAP, Inc. All rights reserved.

Mathematical Contest in Modeling (MCM)?, High School Mathematical Contest in

Modeling (HiMCM)?, and Interdisciplinary Contest in Modeling (ICM)? are registered trade marks of COMAP, Inc.

Vol. 31, No. 2 2010

Table of Contents

Editorial

The Modeling Contests in 2010

Paul J. Campbell............................................................................. 93 MCM Modeling Forum

Results of the 2010 Mathematical Contest in Modeling

Frank R. Giordano .......................................................................... 95 The Sweet Spot: AWave Model of Baseball Bats

Yang Mou, Peter Diao, and Rajib Quabili ....................................... 105 Judges’ Commentary: The Outstanding Sweet Spot Papers

Michael Tortorella......................................................................... 123 Centroids, Clusters, and Crime: Anchoring the Geographic Profiles of Serial Criminals

Anil S. Damle, Colin G.West, and Eric J. Benzel.............................. 129 Judges’ Commentary: The Outstanding Geographic Profiling Papers Marie Vanisko .............................................................................. 149 Judges’ Commentary: The Fusaro Award for the

Geographic Profiling Problem

Marie Vanisko and Peter Anspach ................................................. 153 ICM Modeling Forum

Results of the 2010 Interdisciplinary Contest in Modeling

Chris Arney ................................................................................. 157 Shedding Light on Marine Pollution

Brittany Harris, Chase Peaslee, and Kyle Perkins ............................ 165 Author’s Commentary: The Marine Pollution Problem

Miriam C. Goldstein ..................................................................... 175 Judges’ Commentary: The Outstanding Marine Pollution Papers Rodney Sturdivant........................................................................ 179

Editorial 93

Editorial

The 2010 Modeling Contests

Paul J. Campbell

Mathematics and Computer Science

Beloit College

Beloit, WI 53511–5595

campbell@beloit.edu

Background

Based on Ben Fusaro‘s suggestion for an ―applied Putnam‖ contest, in 1985 COMAP introduced theMathematicalContest inModeling (MCM)!R . Since then, this Journal has devoted an issue each year to the Outstanding contest papers. Even after substantial editing, that issue has sometimes run

to more than three times the size of an ordinary issue. From 2005 through 2009, some papers appeared in electronic form only.

The 2,254 MCM teams in 2010 was almost double the number in 2008.

Also, since the introduction in 1999 of the Interdisciplinary Contest in Modeling (ICM)!R (which has separate funding and sponsorship from the MCM), the Journal has devoted a second of its four annual issues to Outstanding

papers from that contest.

A New Designation for Papers

It has become increasingly difficult to identify just a handful of Outstanding papers for each problem. After 14 Outstanding MCM teams in

2007, there have been 9 in each year since, despite more teams competing.

The judges have been overwhelmed by increasing numbers of Meritorious papers from which to select the truly Outstanding. As a result, this

year there is a new designation of Finalist teams, between Outstanding and Meritorious. It recognizes the less than 1% of papers that reached the final (seventh) round of judging but were not selected as Outstanding. Each Finalist paper displayed some modeling that distinguished it from the rest of the Meritorious papers. We think that the Finalist papers deserve special The UMAP Journal 31 (2) (2010) 93–94. !c Copyright 2010 by COMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 94 The UMAP Journal 31.2 (2010)

recognition, and the mathematical professional societies are investigating ways to recognize the Finalist papers.

Just One Contest Issue Each Year

Taking up two of the four Journal issues each year, and sometimes twothirds

of the pages, the amount of material from the two contests has come to overbalance the other content of the Journal.

The Executive Publisher, Sol Garfunkel, and I have decided to return more of the Journal to its original purpose, as set out 30 years ago, to: acquaint readers with a wide variety of professional applications of the mathematical sciences, and provide a forumfor discussions of new directions in mathematical education.

[Finney and Garfunkel 1980, 2–3]

Henceforth, we plan to devote just a single issue of the Journal each year to the two contests combined. That issue—this issue—will appear during the summer and contain

?reports on both contests, including the problem statements and names

of the Outstanding teams and their members;

?authors‘, judges‘, and practitioners‘ commentaries (as available) on the problems and the Outstanding papers; and

?just one Outstanding paper from each problem.

Available separately from COMAP on a CD-ROM very soon after the contests (as in 2009 and again this year) will be:

?full original versions of all of the Outstanding papers, and

?full results for all teams.

Your Role

The ever-increasing engagement of students in the contests has been astonishing; the steps above help us to cope with this success.

There will now be more room in the Journal for material on mathematical modeling, applications of mathematics, and ideas and perspectives on mathematics education at the collegiate level—articles, UMAP Modules, Minimodules, ILAP Modules, guest editorials. We look forward to your contribution.

Reference

Finney, Ross L., and Solomon Garfunkel. 1980. UMAP and The UMAP Journal.

The UMAP Journal 0: 1–4.

Results of the 2010 MCM 95

Modeling Forum

Results of the 2010

Mathematical Contest in Modeling Frank R. Giordano, MCM Director

Naval Postgraduate School

1 University Circle

Monterey, CA 93943–5000

frgiorda@nps.edu

Introduction

A total of 2,254 teams of undergraduates from hundreds of institutions and departments in 14 countries, spent a weekend in February working on applied

mathematicsproblems inthe 26thMathematicalContest inModeling(MCM)!R . The 2010MCMbegan at 8:00 P.M. EST on Thursday, February 18, and ended at 8:00 P.M. EST on Monday, February 22. During that time, teams of up to three undergraduates researched, modeled, and submitted a solution to one of two open-ended modeling problems. Students registered, obtained contest materials, downloaded the problem and data, and entered completion data through COMAP‘s MCM Website. After a weekend of hard work, solution

papers were sent to COMAP on Monday. Two of the top papers appear in this issue of The UMAP Journal, together with commentaries.

In addition to this special issue of The UMAP Journal, COMAP has made available a special supplementary 2010 MCM-ICM CD-ROM containing the press releases for the two contests, the results, the problems, and original versions

of the Outstanding papers. Information about ordering the CD-ROM is at /product/cdrom/index.html or from (800) 772–6627.

Results and winning papers from the first 25 contests were published in special issues of Mathematical Modeling (1985–1987) and The UMAP Journal

(1985–2009). The 1994 volume of Tools for Teaching, commemorating the tenth

anniversary of the contest, contains the 20 problems used in the first 10 years of the contest and a winning paper for each year. That volume and the special The UMAP Journal 31 (2) (2010) 95–104. !c Copyright 2010 by COMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 96 The UMAP Journal 31.2 (2010)

MCMissues of the Journal for the last few years are available fromCOMAP. The

1994volumeis also availableonCOMAP‘sspecial ModelingResourceCD-ROM. Also available is The MCM at 21 CD-ROM, which contains the 20 problems from the second 10 years of the contest, a winning paper from each year, and advice from advisors of Outstanding teams. These CD-ROMs can be ordered from COMAP at /product/cdrom/index.html . This year, the two MCM problems represented significant challenges: ?Problem A, ―The Sweet Spot,‖ asked teams to explain why the spot on a baseball bat where maximum power is transferred to the ball is not at the end of the bat and to determine whether ―corking‖ a bat (hollowing it out and replacing the hardwood with cork) enhances the ―sweet spot‖ effect. ?Problem B, ―Criminology,‖ asked teams to develop geographical profiling

to aid police in finding serial criminals.

In addition to the MCM, COMAP also sponsors the Interdisciplinary Contest in Modeling (ICM)!R and the High School Mathematical Contest in Modeling (HiMCM)!R :

?The ICM runs concurrently with MCM and for the next several years will offer a modeling problem involving an environmental topic. Results of this year‘s ICM are on the COMAP Website at / undergraduate/contests. The contest report, an Outstanding paper, and commentaries appear in this issue.

?The HiMCM offers high school students a modeling opportunity similar to the MCM. Further details about the HiMCM are at http://www.comap. com/highschool/contests .

2010 MCM Statistics

?2,254 teams participated

?15 high school teams (<1%)

?358 U.S. teams (21%)

?1,890 foreign teams (79%), from Australia, Canada, China, Finland, Germany,

Indonesia, Ireland, Jamaica, Malaysia, Pakistan, Singapore, South

Africa, United Kingdom

?9 OutstandingWinners (<0.5%)

?12 Finalists (0.5%)

?431 MeritoriousWinners (19%)

?542 Honorable Mentions (24%)

?1,245 Successful Participants (55%)

Results of the 2010 MCM 97

Problem A: The Sweet Spot

Explain the ―sweet spot‖ on a baseball bat. Every hitter knows that there is a spot on the fat part of a baseball bat where maximum power is transferred to the ballwhenhit. Whyisn‘t this spot at the end of the bat? Asimple explanation based on torque might seem to identify the end of the bat as the sweet spot,

but

this is known to be empirically incorrect. Develop a model that helps explain this empirical finding.

Some players believe that ―corking‖ a bat (hollowing out a cylinder in the head of the bat and filling it with cork or rubber, then replacing a wood cap) enhances the ―sweet spot‖ effect. Augment your model to confirm or deny this effect. Does this explain why Major League Baseball prohibits ―corking‖? Does the material out of which the bat is constructed matter? That is, does this model predict different behavior for wood (usually ash) or metal (usually aluminum) bats? Is this why Major League Baseball prohibits metal bats? Problem B: Criminology

In 1981, Peter Sutcliffe was convicted of 13murders and subjecting a number of other people to vicious attacks. Oneof the methods used to narrowthe search

for Mr. Sutcliffe was to find a ―center of mass‖ of the locations of the attacks. In the end, the suspect happened to live in the same town predicted by this technique. Since that time, a number of more sophisticated techniques have been developed to determine the ―geographical profile‖ of a suspected serial criminal based on the locations of the crimes.

Your team has been asked by a local police agency to develop a method to aid in their investigations of serial criminals. The approach that you develop should make use of at least two different schemes to generate a geographical profile. You should develop a technique to combine the results of the different schemes and generate a useful prediction for law enforcement officers. The prediction should provide some kind of estimate or guidance about possible locations of the next crime based on the time and locations of the past crime scenes. If you make use of any other evidence in your estimate, you must provide specific details about how you incorporate the extra information. Your method should also provide some kind of estimate about how reliable the estimate will be in a given situation, including appropriate warnings.

In addition to the required one-page summary, your report should include an additional two-page executive summary. The executive summary should provide a broad overview of the potential issues. It should provide an overview of your approach and describe situations when it is an appropriate tool and situations in which it is not an appropriate tool. The executive summary will be read by a chief of police and should include technical details appropriate to the intended audience.

98 The UMAP Journal 31.2 (2010)

The Results

The solution papers were coded at COMAP headquarters so that names and affiliations of the authors would be unknown to the judges. Each paper was then read preliminarily by two ―triage‖ judges at either Appalachian State

University (Sweet Spot Problem) or at the National Security Agency (Criminology

Problem). At the triage stage, the summary and overall organization

are the basis for judging a paper. If the judges‘ scores diverged for a paper, the judges conferred; if they still did not agree, a third judge evaluated the paper. AdditionalRegionalJudgingsiteswere created at the U.S. MilitaryAcademy and at the Naval Postgraduate School to support the growing number of contest

submissions.

Final judging took place at the Naval Postgraduate School, Monterey, CA. The judges classified the papers as follows:

Honorable Successful

Outstanding Finalist Meritorious Mention Participation Total

Sweet Spot Problem 4 5 180 217 533 939

Criminology Problem 5 7 251 325 712 1300

9 12 431 542 1245 2239

We list here the 9 teams that the judges designated as Outstanding; the list of all participating schools, advisors, and results is at the COMAPWebsite. Outstanding Teams

Institution and Advisor Team Members

Sweet Spot Problem

―An Optimal Model of ?Sweet Spot‘ Effect‖

Huazhong University of Science and

Technology

Wuhan, Hubei, China

Liang Gao

Zhe Xiong

Qipei Mei

Fei Han

―The Sweet Spot: AWave Model of

Baseball Bats‖

Princeton University

Princeton, NJ

Robert Calderbank

Yang Mou

Peter Diao

Rajib Quabili

Results of the 2010 MCM 99

―Brody Power Model: An Analysis of Baseball‘s

?Sweet Spot‘‖

U.S. Military Academy

West Point, NY

Elizabeth Schott

David Covell

Ben Garlick

ChandlerWilliams

―An Identification of ?Sweet Spot‘‖

Zhejiang University

Hangzhou, China

Xinxin Xu

Cong Zhao

Yuguang Yang

Zuogong Yue

Criminology Papers

―Predicting a Serial Criminal‘s Next Crime Location Using Geographic Profiling‖

Bucknell University

Lewisburg, PA

Nathan C. Ryan

BryanWard

RyanWard

Dan Cavallaro

―Following the Trail of Data‖

Rensselaer Polytechnic Institute

Troy, NY

Peter R. Kramer

Yonatan Naamad

Joseph H. Gibney

Emily P. Meissen

―From Kills to Kilometers: Using Centrographic Techniques and Rational Choice Theory for Geographical Profiling of Serial Killers‖

Tufts University

Medford, MA

Scott MacLachlan

Daniel Brady

Liam Clegg

Victor Minden

―Centroids, Clusters, and Crime: Anchoring the Geographic Profile of Serial Criminals‖

University of Colorado—Boulder

Boulder, CO

Anne M. Dougherty

Anil S. Damle

Colin G.West

Eric J. Benzel

―Tracking Serial Criminals with a Road Metric‖ University ofWashington

Seattle,WA

James Allen Morrow

Ian Zemke

Mark Bun

Jerry Li

100 The UMAP Journal 31.2 (2010)

Awards and Contributions

Each participatingMCMadvisor and teammemberreceived a certificate signed by the Contest Director and the appropriate Head Judge.

INFORMS, the Institute for Operations Research and the Management Sciences, recognized the teams fromPrinceton University (Sweet Spot Problem)

and Tufts University (Criminology Problem) as INFORMS Outstanding teams and provided the following recognition:

?a letter of congratulations from the current president of INFORMS to each team member and to the faculty advisor;

?a check in the amount of $300 to each team member;

?a bronze plaque for display at the team‘s institution, commemorating team members‘ achievement;

?individual certificates for team members and faculty advisor as a personal commemoration of this achievement; and

?a one-year student membership in INFORMS for each team member, which includes their choice of a professional journal plus the OR/MS Today periodical and the INFORMS newsletter.

The Society for Industrial and Applied Mathematics (SIAM) designated one Outstanding team from each problem as a SIAM Winner. The teams were from Huazhong University of Science and Technology (Sweet Spot Problem)andRensselaer Polytechnic Institute (CriminologyProblem). Each of the team memberswas awarded a $300 cash prize, and the teams received

partial expenses to present their results in a special Minisymposium at the SIAM Annual Meeting in Pittsburgh, PA in July. Their schools were given a framed hand-lettered certificate in gold leaf.

The Mathematical Association of America (MAA) designated one Outstanding

North American team from each problem as an MAA Winner.

The teams were from the U.S. Military Academy (Sweet Spot Problem) and the University of Colorado—Boulder (Criminology Problem). With partial

travel support from the MAA, the teams presented their solution at a special session of the MAA Mathfest in Pittsburgh, PA in August. Each team member was presented a certificate by an official of the MAA Committee on Undergraduate Student Activities and Chapters.

Ben Fusaro Award

OneMeritorious or Outstandingpaperwasselected for each problem for the Ben Fusaro Award, named for the Founding Director of the MCM and awarded for the seventh time this year. It recognizes an especially creative approach; details concerning the award, its judging, and Ben Fusaro are in Results of the 2010 MCM 101

Vol. 25 (3) (2004): 195–196. The Ben Fusaro Award winners were Princeton

University (Sweet Spot Problem) and Duke University (Criminology Problem). A commentary on the latter appears in this issue.

Judging

Director

Frank R. Giordano, Naval Postgraduate School, Monterey, CA

Associate Director

William P. Fox, Dept. of Defense Analysis, Naval Postgraduate School, Monterey, CA

Sweet Spot Problem

Head Judge

Marvin S. Keener, Executive Vice-President, Oklahoma State University, Stillwater, OK

Associate Judges

William C. Bauldry, Chair, Dept. of Mathematical Sciences,

Appalachian State University, Boone, NC (Head Triage Judge)

Patrick J. Driscoll, Dept. of Systems Engineering, U.S. Military Academy, West Point, NY (INFORMS Judge)

J. Douglas Faires, Youngstown State University, Youngstown, OH

Ben Fusaro, Dept. of Mathematics, Florida State University, Tallahassee, FL

(SIAM Judge)

Michael Jaye, Dept. of Mathematical Sciences, Naval Postgraduate School, Monterey, CA

John L. Scharf, Mathematics Dept., Carroll College, Helena, MT (MAA Judge)

Michael Tortorella, Dept. of Industrial and Systems Engineering, Rutgers University, Piscataway, NJ (Problem Author)

Richard DouglasWest, Francis Marion University, Florence, SC

Criminology Problem

Head Judge

Maynard Thompson, Mathematics Dept., University of Indiana, Bloomington, IN

Associate Judges

Peter Anspach, National Security Agency, Ft. Meade, MD

(Head Triage Judge)

Kelly Black, Mathematics Dept., Union College, Schenectady, NY 102 The UMAP Journal 31.2 (2010)

Jim Case (SIAM Judge)

William P. Fox, Dept. of Defense Analysis, Naval Postgraduate School, Monterey, CA

Frank R. Giordano, Naval Postgraduate School, Monterey, CA

Veena Mendiratta, Lucent Technologies, Naperville, IL

David H. Olwell, Naval Postgraduate School, Monterey, CA

Michael O‘Leary, Towson State University, Towson, MD (Problem Author) Kathleen M. Shannon, Dept. of Mathematics and Computer Science, Salisbury University, Salisbury, MD (MAA Judge)

Dan Solow, CaseWestern Reserve University, Cleveland, OH

(INFORMS Judge)

Marie Vanisko, Dept. of Mathematics, Carroll College, Helena, MT (Ben Fusaro Award Judge)

Regional Judging Session at U.S. Military Academy

Head Judges

Patrick J. Driscoll, Dept. of Systems Engineering,

United States Military Academy (USMA),West Point, NY

Associate Judges

Tim Elkins, Dept. of Systems Engineering, USMA

Darrall Henderson, Sphere Consulting, LLC

Steve Horton, Dept. of Mathematical Sciences, USMA

Tom Meyer, Dept. of Mathematical Sciences, USMA

Scott Nestler, Dept. of Mathematical Sciences, USMA

Regional Judging Session at Naval Postgraduate School

Head Judges

William P. Fox, Dept. of Defense Analysis, Naval Postgraduate School, Monterey, CA

Frank R. Giordano, Naval Postgraduate School, Monterey, CA

Associate Judges

Matt Boensel, Robert Burks, Peter Gustaitis, Michael Jaye, and Greg Mislick

—all from the Naval Postgraduate School, Monterey, CA

Triage Session for Sweet Spot Problem

Head Triage Judge

William C. Bauldry, Chair, Dept. of Mathematical Sciences,

Appalachian State University, Boone, NC

Associate Judges

Jeffry Hirst, Greg Rhoads, and Kevin Shirley

—all from Dept. of Mathematical Sciences, Appalachian State University, Boone, NC

Results of the 2010 MCM 103

Triage Session for Criminology Problem

Head Triage Judge

Peter Anspach, National Security Agency (NSA), Ft. Meade, MD Associate Judges

Jim Case

Other judges from inside and outside NSA, who wish not to be named. Sources of the Problems

The Sweet Spot Problem was contributed by Michael Tortorella (Rutgers University), and the Criminology Problem by Michael O‘Leary (Towson University) and Kelly Black (Clarkson University).

Acknowledgments

Major funding for theMCMis providedby the National SecurityAgency (NSA) and by COMAP. Additional support is provided by the Institute for Operations Research and the Management Sciences (INFORMS), the Society

for Industrial and Applied Mathematics (SIAM), and the Mathematical Association of America (MAA).We are indebted to these organizations for providing judges and prizes.

We also thank for their involvement and support the MCM judges and MCM Board members for their valuable and unflagging efforts, as well as ?Two Sigma Investments. (This group of experienced, analytical, and technical financial professionals based in New York builds and operates sophisticated quantitative trading strategies for domestic and international markets. The firm is successfully managing several billion dollars using highly-automated trading technologies. For more information about Two Sigma, please visit .)

?Jane Street Capital, LLC. (This proprietary trading firm operates around the clock and around the globe. ―We bring a deep understanding of

markets, a scientific approach, and innovative technology to bear on the problem of trading profitably in the world‘s highly competitive financial markets, focusing primarily on equities and equity derivatives. Founded in 2000, Jane Street employes over 200 people in offices in new York, London,

and Tokyo. Our entrepreneurial culture is driven by our talented

team of traders and programmers.‖ For more information about Jane Street Capital, please visit .)

104 The UMAP Journal 31.2 (2010)

Cautions

To the reader of research journals:

Usually a published paper has been presented to an audience, shown to colleagues, rewritten, checked by referees, revised, and edited by a journal

editor. Each paper here is the result of undergraduates working on

a problem over a weekend. Editing (and usually substantial cutting) has taken place; minor errors have been corrected, wording altered for clarity or economy, and style adjusted to that of The UMAP Journal. The student authors have proofed the results. Please peruse their efforts in that context. To the potential MCM Advisor:

It might be overpowering to encounter such output from a weekend

of work by a small team of undergraduates, but these solution papers are highly atypical. A team that prepares and participates will have an enriching learning experience, independent of what any other team does.

COMAP‘sMathematicalContest in ModelingandInterdisciplinaryContest in Modeling are the only international modeling contests in which students work in teams. Centering its educational philosophy on

mathematical

modeling, COMAP uses mathematical tools to explore real-world

problems. It serves the educational community as well as the world of work by preparing students to become better-informed and better-prepared citizens.

Editor’s Note

The complete roster of participating teams and results has become too long to reproduce in the printed copy of the Journal. It can now be found at the COMAPWebsite, in separate files for each problem:

/undergraduate/contests/mcm/contests/ 2010/results/2010_MCM_Problem_A.pdf

/undergraduate/contests/mcm/contests/ 2010/results/2010_MCM_Problem_B.pdf

The Sweet Spot 105

The Sweet Spot: AWave Model of Baseball Bats

Rajib Quabili

Peter Diao

Yang Mou

Princeton University

Princeton, NJ

Advisor: Robert Calderbank

Abstract

We determine the sweet spot on a baseball bat. We capture the essential physics of the ball–bat impact by taking the ball to be a lossy spring and the bat to be an Euler-Bernoulli beam. To impart some intuition about the model, we begin by presenting a rigid-body model. Next, we use our full model to reconcile various correct and incorrect claims about the sweet spot found in the literature. Finally, we discuss the sweet spot and the performances of corked and aluminum bats, with a particular emphasis on hoop modes. Introduction

Although a hitter might expect a model of the bat–baseball collision to yield insight into how the bat breaks, how the bat imparts spin on the ball, how best to swing the bat, and so on, we model only the sweet spot. There are at least two notions of where the sweet spot should be—an impact location on the bat that either

?minimizes the discomfort to the hands, or

?maximizes the outgoing velocity of the ball.

We focus exclusively on the second definition.

The velocity of the ball leaving the bat is determined by

?the initial velocity and rotation of the ball,

?the initial velocity and rotation of the bat,

TheUMAPJournal 31 (2) (2010) 105–122. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 106 The UMAP Journal 31.2 (2010)

?the relative position and orientation of the bat and ball, and

?the force over time that the hitter‘s hands applies on the handle.

We assume that the ball is not rotating and that its velocity at impact is perpendicular to the length of the bat. We assume that everything occurs in a single plane, and we will argue that the hands‘ interaction is negligible. In the frame of reference of the center of mass of the bat, the initial conditions

are completely specified by

?the angular velocity of the bat,

?the velocity of the ball, and

?the position of impact along the bat.

The location of the sweet spot depends not on just the bat alone but also on the pitch and on the swing.

The simplest model for the physics involved has the sweet spot at the center of percussion [Brody 1986], the impact location that minimizes discomfort

to the hand. The model assumes the ball to be a rigid body for which there are conjugate points: An impact at one will exactly balance the angular

recoil and linear recoil at the other. By gripping at one and impacting at the other (the center of percussion), the hands experience minimal shock and the ball exits with high velocity. The center of percussion depends heavily on the moment of inertia and the location of the hands. We cannot accept this model because it both erroneously equates the two definitions of sweet spot and furthermore assumes incorrectly that the bat is a rigid body. Another model predicts the sweet spot to be between nodes of the two lowest natural frequencies of the bat [Nathan 2000]. Given a free bat allowed

to oscillate, its oscillations can be decomposed into fundamental

modes of various frequencies. Different geometries and materials have different

natural frequencies of oscillation. The resulting wave shapes suggest how to excite those modes (e.g., plucking a string at the node of a vibrational

mode will not excite that mode). It is ambiguous which definition

of sweet spot this model uses. Using the first definition, it would focus on the uncomfortable excitations of vibrational modes: Choosing the impact location to be near nodes of important frequencies, a minimum of uncomfortable

vibrations will result. Using the second definition, the worry is

that energy sent into vibrations of the bat will be lost. This model assumes that the most important energies to model are those lost to vibration. This model raises many questions. Which frequencies get excited and why? The Fourier transform of an impulse in general contains infinitely many modes. Furthermore, wood is a viscoelastic material that quickly dissipates its energies. Is the notion of an oscillating bat even relevant to modeling a bat? How valid is the condition that the bat is free? Ought the system be coupled with hands on the handle, or the arm‘s bone structure,

or possibly even the ball? What types of oscillations are relevant? A cylinThe

Sweet Spot 107

drical structure can support numerous different types of modes beyond the transverse modes usually assumed by this model [Graff 1975].

Following the center-of-percussion line of reasoning, how do we model the recoil of the bat? Following the vibrational-nodes line of reasoning, how do we model the vibrations of the bat? In the general theory of impact mechanics [Goldsmith 1960], these two effects are the main ones (assuming

that the bat does not break or deform permanently). Brody [1986] ignores vibrations, Cross [1999] ignores bat rotation but studies the propagation of the impulse coupled with the ball, and Nathan [2000] emphasizes vibrational

modes. Our approach reconciles the tensionamongthese approaches

while emphasizing the crucial role played by the time-scale of the collision. Our main goal is to understand the sweet spot. A secondary goal is to understand the differences between the sweet spots of different bat types. Although marketers of bats often emphasize the sweet spot, there are other relevant factors: ease of swing, tendency of the bat to break, psychological effects, and so on. We will argue that it doesn‘t matter to the collision whether the batter‘s hands are gripping the handle firmly or if the batter follows through on the swing; these circumstances have no bearing on the technique required to swing the bat or how the bat‘s properties affect it. Our paper is organized as follows. First, we present the Brody rigidbody model, illuminating the recoil effects of impact. Next we present a

full computational model based on wave propagation in an Euler-Bernoulli beam coupled with the ball modeled as a lossy spring. We compare this model with others and explore the local nature of impact, the interaction of recoil and vibrations, and robustness to parameter changes. We adjust the parameters of the model to comment on the sweet spots of corked bats and aluminum bats. Finally, we investigate the effect of hoop frequencies on aluminum bats.

A Simple Example

We begin by considering only the rigid recoil effects of the bat–ball collision, much as in Brody [1986]. For simplicity, we assume that the bat is

perfectly rigid. Because the collision happens on such a short time-scale (around 1 ms), we treat the bat as a free body. That is to say, we are not concerned with the batter‘s hands exerting force on the bat that may be transferred to the ball.

The bat has mass M and moment of inertia I about its center of mass. From the reference frame of the center of mass of the bat just before the

collision, the ball has initial velocity vi in the positive x-direction while the bat has initial angular velocity ωi. In our setup, vi and ωi have opposite signs when the batter is swinging at the ball as in Figure 1, in which arrows point in the positive directions for the corresponding parameters. 108 The UMAP Journal 31.2 (2010)

Figure 1. The collision.

The ball collides with the bat at a distance

l from the center of mass of the bat.

We assume that the collision is head-on and

viewthe event such that all the y-component

velocities are zero at the moment of the collision.

After the collision, the ball has a final

velocity vf and the bat has a final linear velocity

Vf and an angular velocity ωf at the

center of mass.

Whenthe ball hits the bat, the ball briefly

compresses and decompresses, converting

kinetic energy to potential energy and back.

However, some energy is lost in the process,

that is, the collision is inelastic. The ratio of

the relative speeds of the bat and the ball

before and after the collision is known as

the coefficient of restitution, customarily designated

by e: e = 0 represents a perfectly

inelastic collision, and e = 1 means a perfectly elastic one. In this basic model, we make two simplifying assumptions:

?e is constant along the length of the bat, and

?e is constant for all vi.

Given our pre-collision conditions, we can write:

Conservation of linear momentum:

MVf = m(vi ?vf )

Conservation of angular momentum:

I(ωf ?ωi) = ml(vi ?vf ),

Definition of the coefficient of restitution:

e(vi ?ωil) = ?vf + Vf + wf l.

Solving for vf gives

vf = ?vi(e ?m

M?) + ωil(1 + e)

1 + m

M?

,

where

M?= M

1 + Ml2

I

is the effective mass of the bat.

The Sweet Spot 109

For calibration purposes, we use the following data, which are typical

of a regulation bat connecting with a fastball in Major League Baseball. The results are plotted in Figure 2.

m 0.145 kg 5.1 oz

M 0.83 kg 29 oz

L 0.84 m 33 in

I 0.039 kg ·m2

vi 67 m/s 150 mph

ωi ?60 rad/s

e 0.55

Figure 2. Final velocity vf (solid arc at top), swing speed ωil (dotted rising line), and effective mass (dashed falling curve) as a function of distance l (in meters) from center of mass.

The maximum exit velocity is 27 m/s, and the sweet spot is 13 cm from

the center of mass. Missing the sweet spot by up to 5 cm results in at most 1 m/s difference from the maximum velocity, implying a relatively wide sweet spot.

From this example, we see that the sweet spot is determined by a multitude of factors, including the length, mass, and shape of the baseball bat;

the mass of the baseball; and the coefficient of restitution between bat and ball. Furthermore, the sweet spot is not uniquely determined by the bat and ball: It depends also on the incoming baseball speed and the batter‘s swing speed.

Figure 2 also shows intuitivelywhythe sweet spot is located somewhere betweenthe center of massandthe end of the barrel. Asthe point of collision moves outward along the bat, the effective mass of the bat goes up, so that a greater fraction of the initial kinetic energy is put into the bat‘s rotation. At the same time, the rotation in the bat means that the barrel of the bat is moving faster than the center of mass (or handle). These two effects work in

opposite directions to give a unique sweet spot that‘s not at either endpoint. 110 The UMAP Journal 31.2 (2010)

However, this model tells only part of the story. Indeed, some of our starting assumptions contradict each other:

?We treated the bat as a free body because the collision time was so short. In essence, during the 1 ms of the collision, the ball ―sees‖ only the local geometry of the bat, not the batter‘s hands on the handle. On the other hand, we assumed that the bat was perfectly rigid—but that means that the ball ―sees‖ the entire bat.

?We also assumed that e is constant along the length of the bat and for different collision velocities. Experimental evidence [Adair 1994] suggests that neither issue can be ignored for an accurate prediction of the location of the sweet spot.

We need a more sophisticated model to address these shortcomings. Our Model

We draw from Brody‘s rigid-body model but more so from Cross [1999]. One could describe our work as an adaptation of Cross‘s work to actual baseball bats. Nathan [2000] attempted such an adaptation but was misled by incorrect intuition about the role of vibrations. We describe his approach and error as a way to explain Cross‘s work and to motivate our work. Previous Models

Brody‘s rigid-body model correctly predicts the existence of a sweet spot not at the end of the bat. That model suffers from the fact that the bat is not a rigid body and experiences vibrations. One way to account for vibrations

is to model the bat as a flexible object. Beam theories (of varying degrees of

accuracy and complication) can model a flexible bat. Van Zandt [1992] was the first to carry out such an analysis, modeling the beam as a Timoshenko beam, a fourth-order theory that takes into account both shear forces and tensile stresses. The equations are complicated and we will not need them. Van Zandt‘s model assumes the ball to be uncoupled from the beam and simply takes the impulse of the ball as a given. The resulting vibrations of the bat are used to predict the velocity of the beam at the impact point (by summing the Brody velocity with the velocity of the displacement at the impact point due to vibrations) and thence the exit velocity of the ball from the equations of the coefficient of restitution [van Zandt 1992].

Cross [1999] modeled the interaction of the impact of a ball with an aluminum

beam, using the less-elaborate Euler-Bernoulli equations to model the propagation of waves. In addition, he provided equations to model the dynamic coupling of the ball to the beam during the impact. After discretizing

the beam spatially, he assumed that the ball acts as a lossy spring coupled to the single component of the region of impact.

The Sweet Spot 111

Cross‘s work was motivated by both tennis rackets and baseball bats, which differ importantly in the time-scale of impact. The baseball bat‘s collision

lasts only about 1 ms, during which the propagation speed of the wave is very important. In this local view of the impact, the importance of the baseball‘s coupling with the bat is increased.

Cross argues that the actual vibrational modes and node points are largely irrelevant because the interaction is localized on the bat. The boundary

conditions matter only if vibrations reflect off the boundaries; an impact not close enough to the barrel end of the bat will not be affected by

the boundary there. In particular, a pulse reflected from a free boundary returns with the same sign (deflected away from the ball, decreasing the force on the ball, decreasing the exit velocity), but a pulse reflected from a fixed boundary returns with the opposite sign (deflected towards the ball, pushing it back, increasing the exit velocity). Away from the boundary, we expect the exit velocity to be uniform along a non-rotating bat. Cross‘s model predicts all of these effects, and he experimentally verified them. In our model, we expect similar phenomena, plus the narrowing of the barrel near the handle to act somewhat like a boundary.

Nathan‘s model also attempted to combine the best features of Van

Zandt and Cross [Nathan 2000]. His theory used the full Timoshenko theory for the beam and the Cross model for the ball. He even acknowledged

the local nature of impact. So where do we diverge from him? His error stems from an overemphasis on trying to separate out the ball‘s interaction with each separate vibrational mode.

The first sign of inconsistency comes when he uses the ―orthogonality of the eigenstates‖ to determine how much a given impulse excites each mode. The eigenstates are not orthogonal. Many theories yield symmetric matrices that need to be diagonalized, yielding the eigenstates; but Timoshenko‘s

theory does not, due to the presence of odd-order derivatives

in its equations. Nathan‘s story plays out beautifully if only the eigenstates were actually orthogonal; but we have numerically calculated the

eigenstates, and they are not even approximately orthogonal. He uses the orthogonality to draw important conclusions:

?The location of the nodes of the vibrational modes are important. ?High-frequency effects can be completely ignored.

We disagree with both of these.

The correct derivation starts with the following equation of motion, where k is the position of impact, yi is the displacementandFi is the external force on the ith segment of the bat, and Hij is an asymmetric matrix: y00 k (t) = Hkjyj(t) + Fk(t).

We write the solutions as yk(t) = Φknan(t), where the rows of Φkn are eigenmodes with eigenvalues?ω2n

. Explicitly,HjkΦkn = ?ω2n

Φjn, andΦkn

112 The UMAP Journal 31.2 (2010)

indicates the kth component of the nth eigenmode. Then we write the equation of motion:

Φkna00 n(t) + Φknω2n

an(t) = Fk = ΦknΦ?1

nj Fj ,

a00 n(t) + ω2n

an(t) = Φ?1

nkFk.

In the last step, we used the fact that the eigenmodes form a complete basis.

Nathan‘s paper uses on the right-hand side simply ΦknFk scaled by

a normalization constant. At first glance, this seems like a minor technical detail, but the physics here is important. We calculate that the Φ?1 nkFk

terms stay fairly large for even high values of n, corresponding to the highfrequency

modes (k is just the position of the impact). This means that

there are significant high-frequency components, at least at first. In fact, the high-frequencymodesare necessary for the impulse to propagate slowly as a wave packet. In Nathan‘s model, only the lowest standing modes are excited; so the entire bat starts vibrating as soon as the ball hits. This contradicts

his earlier belief in localized collision (which we agree with), that the

collision is over so quickly that the ball ―sees‖ only part of the bat. Nathan also claims that the sweet spot is related to the nodes of the lowest mode, which contradicts locality: The location of the lowest-order nodes depends on the geometry of the entire bat, including the boundary conditions at the handle.

While the inconsistencies in the Nathan model may cancel out, we build our model on a more rigorous footing. For simplicity, we use the Euler- Bernoulli equations rather than the full Timoshenko equations. The difference

is that the former ignore shear forces. This should be acceptable;

Nathan points out that his model is largely insensitive to the shear modulus. We solve the differential equations directly after discretizing in space rather than decomposing into modes. In these ways, we are following the work of Cross [1999].

On the other hand, our model extends Cross‘s work in several key ways: ?We examineparametersmuchcloser to those relevant to baseball. Cross‘s models focused on tennis, featuring an aluminum beam of width 0.6 cm being hit with a ball of 42 g at around 1 m/s. For baseball, we have an aluminum or wood bat of radius width 6 cm being hit with a ball of 145 g

traveling at 40 m/s (which involves 5,000 times as much impact energy). ?We allow for a varying cross-section, an important feature of a real bat. ?We allow the bat to have some initial angular velocity. This will let us scrutinize the rigid-body model prediction that higher angular velocities lead to the maximum power point moving farther up the barrel. To reiterate, the main features of our model are

?an emphasis on the ball coupling with the bat,

The Sweet Spot 113

?finite speed of wave propagation in a short time-scale, and

?adaptation to realistic bats.

These are natural outgrowths of the approaches in the literature. Mathematics of Our Model

Our equations are a discretized version of the Euler-Bernoulli equations: ρ

?2y(z, t)

?t2 = F(z, t) + ?2

?z2

μ

Y I

?2y(z, t)

?z2

?

,

where

ρis the mass density,

y(z, t) is the displacement,

F(z, t) is the external force (in our case, applied by the ball),

Y is the Young‘s modulus of the material (a constant), and

I is the second moment of area (πR4/4 for a solid disc).

We discretize z in steps ofΔ. The only force is from the ball, in the negative direction to the kth segment. Our discretized equation is:

ρAΔd2yi

dt2 = ?δikF(t) ?

Y

Δ3

Σ

Ii?1(yi?2 ?2yi?1 + yi)

?2Ii(yi?1 ?2yi + yi+1) + Ii+1(yi ?2yi+1 + yi+2)

Π

.

Our dynamic variables are y1 through yN. For a fixed left end, we pretend that y?1 = y0 = 0. For a free left end, we pretend that

y1 ?y0 = y0 ?y?1 = y?1 ?y?2.

The conditions on the right end are analogous. These are the same conditions

that Cross uses.

Finally, we have an additional variable for the ball‘s position (relative to some zero point)w(t). Initially, w(t) is positive and w0(t) is negative, so the ball is moving from the positive direction towards the negative. Let u(t) = w(t) ?yk(t). This variable represents the compression of the ball, and we replace F(t) with F

°

u(t), u0(t)

. Initially, u(t) = 0 and u0(t) = ?vball. The

force between the ball and the bat takes the form of hysteresis curves such as the ones shown in Figure 3.

114 The UMAP Journal 31.2 (2010)

Figure 3. A hysteresis curve used in our modeling, with maximum compression 1.5 cm. The higher curve is taken when u0(t) <0 (compression) and the lower curve when u0(t) >0 (expansion). When u(t) >0, the force is zero. The equation of motion for the ball is then

w00(t) = u00(t) + y00 k (t) = F

°

u(t), u0(t)

.

We have eliminated the variable w.

We have yet to specify the function F

°

u(t), u0(t)

. As can be seen in

videos [Baseball Research Center n.d.], the ball compresses significantly (often more than 1 cm) in a collision. The compression and decompression is lossy. We could model this loss by subtracting a fraction of the ball‘s

energy after the collision; that approach is good enough for many purposes, but we instead follow Nathan and use a nonlinear spring with hysteresis. Since W =

R

Fdx, the total energy lost is the area between the two

curves in Figure 3. A problem with creating hysteresis curves is that one does not know the maximum compression (i.e., where to start drawing the bottom curve) until after solving the equations of motion. In practice, we solve the equation in two steps.

The main assumptions of our model derive from the main assumptions of each equation:

?The first is the exact form of the hysteresis curve of the ball. Cross [1999] argues that the exact form of the curve is not very important as long as the duration of impact, magnitude of impulse, maximum compression of the ball, and energy loss are roughly correct.

?Both the Timoshenko and Euler-Bernoulli theories ignore azimuthal and longitudinal waves. This is a fundamental assumption built into all of the approaches in the literature. Assuming that the impact of the ball is transverse and the ball does not rotate, the assumption is justified.

The assumptions of our models are the same as those in the literature, so they are confirmed by the literature‘s experiments.

The Sweet Spot 115

Simulation and Analysis

Simulation Results

Our model‘s two main features are wave propagation in the bat and

nonlinear compression/decompression of the ball. The latter is illustrated by the asymmetry of the plot in Figure 4a. This plot also reveals the timescale

of the collision: The ball leaves the bat 1.4 ms after impact. During and after collision, shock waves propagate through the bat.

In this example, the bat was struck 60cmfromthe handle. What does the collision look like at 10 cm from the handle? Figure 4b shows the answer: The other end of the bat does not feel anything until about 0.4 ms and does not feel significant forces until about 1.0 ms. By the time that portion of the bat swings back (almost 2.0 ms), the ball has already left contact with the bat. This illuminates an important point: We are concerned only with forces on the ball that act within the 1.4 ms time-frame of the collision. Any waves taking longer to return to the impact location do not affect exit velocity. Figure 4.

a. Left: The force between the ball and the bat as a function of time; the impulse lasts 1.4 ms. b. Right: The waveform of y10(t) when the bat is struck at 60 cm. The impulse reaches this chunk

at around 0.4 ms but does not start moving significantly until later.

Having demonstrated the basic features of our model, we now replicate some of Cross‘s results but with baseball-like parameters. In Figure 5a, we show that the effects of fixed- vs. free-boundary conditions are in agreement

with Cross‘s model.

As we expected, fixed boundaries enhance the exit velocity and free

boundaries reduce them. From this result, we see the effect of the shape of the bat. The handle does indeed act like a free boundary. The distance between the boundaries is too small to get a flat zone in the exit velocity vs. position curve. If we extend the barrel by 26 cm, a flat zone develops (Figure

5b; notice the change in axes). Intuitively, this flat zone exists because the ball ―sees‖ only the local geometry of the bat and the boundaries are too far away to have a substantial effect.

From now on, we use an 84-cm bat free on both ends, where position

zero denotes the handle end. In this base case, the sweet spot is at 70 cm. We

116 The UMAP Journal 31.2 (2010)

Figure 5.

a. Left: Exit velocity vs. impact position for a free boundary (solid line) and for a fixed boundary (dashed line), with barrel end fixed but handle end free, for an 84-cm bat

b. Right: The same graph for a free 110-cm bat.

investigate the dependence of the exit speed on the initial angular velocity. According to rigid-body models, the sweet spot is exactly at the center of mass if the bat has no angular velocity. In Figure 6, we present the results of

changing the angular velocity. Our results contrast greatly with the simple example presented earlier. While the angular-rotation effect is still there, the effective mass plays only a negligible role in determining the exit speed. In other words, the bat is not a rigid body because the entire bat does not react instantly. The dominating effect is from the boundaries: the end of the barrel and where the barrel tapers off. These free ends cause a significant drop in exit velocity. Increasing the angular velocity of the bat increases the exit velocity, in part just because the impact velocity is greater (by a factor of ωi times the distance from the center of mass of the bat).

Figure 6. Exit velocity vs. impact position at various initial angular velocities of the bat. Our model predicts the solid curves, while the dashed lines represent the simple model. The dots are at the points where Brody‘s solution is maximized.

The Sweet Spot 117

In Figure 7a, we show that near the sweet spot (at 0.7 m), increasing

angular velocity actually decreases the excess exit velocity (relative to the impact velocity). We should expect this, since at higher impact velocity,

more energy is lost to the ball‘s compression and decompression. To confirm

this result, we also recreate the plot in Figure 7b but without the

hysteresis curve—in which case this effect disappears. This example is one of the few places where the hysteresis curve makes a difference, confirming

experimental evidence [Adair 1994; Nathan 2003] that the coefficient of restitution decreases with increasing impact velocity.

Figure 7.

Exit velocity minus impact velocity vs. impact position, for initial angular velocities of the bat. a. Left: Near the center of mass, higher angular velocity gives higher excess exit velocity, but towards the sweet spot the lines cross and higher angular velocity gives lower excess exit velocity. b. Right: The same plot without a hysteresis curve. The effect disappears.

The results for angular velocity contrast with the simple model. As evident from Figure 8, the rigid-body model greatly overestimates this effect for large angular velocities.

,

Figure 8. Optimal impact position vs. angular velocity. The straight line is the rigid-body prediction, while the points are our model‘s prediction.

Parameter Space Study

There are various adjustable parameters in our model. For the bat, we use density ρ= 649 kg/m3 and Young‘s modulus Y = 1.814 ×1010 N/m2. 118 The UMAP Journal 31.2 (2010)

Figure 9. The profile of our bat.

These values, as well as our bat profile (Figure 9), were used by Nathan as typical values for a wooden bat. While these numbers are in good agreement

with other sources, we will see that these numbers are fairly special.

As a result of our bat profile, the mass is 0.831 kg and the moment of inertia around the center of mass (at 59.3 cm from the handle of our 84 cm bat) is 0.039 kg·m2. We let the 145-g ball‘s initial velocity be 40 m/s, and set up our hysteresis curve so that the compression phase is linear with spring constant 7 ×105 N/m.

?We vary the density of the bat and see that the density value occupies a narrow region that gives peaked exit-velocity curves (see Figure 10). Figure 10.

Exit velocity vs. impact position for various densities. The solid line is the original ρ= 649kg/m3. a. Left: Dotted is ρ= 700, dashed is ρ= 1000. b. Right: Dotted is ρ= 640, dashed is ρ= 500.

?We also vary the Young‘s modulus and shape of bat to similar effect (see Figure 11). The fact that varying any of Nathan‘s parameters makes the resulting exit velocity vs. location plot less peaked means that baseball bats are specially designed to have the shape shown in Figure 9 (or else the parameters were picked in a special way).

?Finally, we vary y, the speed of the ball (see Figure 12). The exit velocity simply scales with the input velocity, as expected.

Alternatives toWooden Bats

Having checked the stability of our model for small parameter changes, we now change the parameters drastically, so as to model corked and aluminum

bats.

The Sweet Spot 119

Figure 11.

a. Left: Varying the value of Y . Solid is Y = 1.1814 ×1010N/m2; dashed is 1.25 times as much, while dotted is 0.8 times.

b. Right: Varying the shape of the bat. Solid is the original shape; dashed has a thicker handle region, while dotted has a narrower handle region.

Figure 12. Varying the speed of the ball. Solid is the original 40 m/s, dashed is 50 m/s, while dotted is 30 m/s.

Corked Bat

We model a corked bat as a wood bat with the barrel hollowed out, leaving a shell 1 cm or 1.5 cm thick. The result is shown in Figure 13a. The exit velocities are higher, but this difference is too small to be taken seriously. This result agrees with the literature: The only advantages of a corked bat are the changes in mass and in moment of inertia.

Aluminum Bat

We model an aluminum bat as a 0.3 cm-thick shell with a density of 2700 kg/m3 and Young‘s modulus 6.9 ×1010 N/m2. The aluminum bat performs much better than the wood bat (Figure 13b). It has the same sweet

spot (70 cm) and similar sweet-spot performance, but the exit velocity falls off more gradually away from the sweet spot.

To gain more insight, we animated the displacement of the bat vs. time; we present two frames of the animation in Figure 14. The aluminum bat is 120 The UMAP Journal 31.2 (2010)

Figure 13. Exit velocity vs. distance of point of collision on the bat from the handle end. a. Corked bat. b. Aluminum bat.

displaced less (absorbing less energy). More importantly, in the right-hand diagram of Figure 14, the curve for the wood bat is still moving down and left, while the aluminum bat‘s curve is moving left and pushing the ball back up. The pulse in the aluminum bat travels faster and returns in time to give energy back to the ball. By the time the pulse for the wood bat returns to the impact location, the ball has already left the bat.

Figure 14. Plots of the displacement of an aluminum bat (dashed) and wood bat (solid) being hit by a ball 60 cm from the handle end. The diagram on the right shows two frames superimposed (t = 1.05 ms and t = 1.10 ms) so as to show the motion. The rigid translation and rotation has been removed from the diagrams.

In the literature, the performance of aluminum bats is often attributed to a ―trampoline effect,‖ in which the bat compresses on impact and then springs back before the end of the collision [Russell 2003]. This effect would improve aluminum-bat performance further. The trampoline effect involves exciting so-called ―hoop modes,‖ modes with an azimuthal dependence,

which our model cannot simulate directly. For an aluminum bat, one

could conceivably use wave equations for a cylindrical sheet (adjusting for the changing radius) and then solve the resulting partial differential equations

in three variables. Analysis of such a complex system of equations is beyond the scope of this paper.

Instead, we artificially insert a hoop mode by hanging a mass from a spring at the spot of the bat where the ball hits. We expect the important The Sweet Spot 121

modes to be the ones with periods near the collision time (1.4 ms, corresponding

to 714 Hz). We find that this mode does affect the sweet spot,

although the exact change does not seem to follow a simple relationship with the frequency. Our results, as shown in Figure 15, show that hoop modes around 700 Hz do enhance the exit velocity. They not only make the sweet spot wider but also shift it slightly toward the barrel end of the bat. Figure 15. Exit velocity vs. impact position at different hoop frequencies. The lines from bottom to top at the left edge (color) are: (blue, starts off the chart) wood bat, (next higher, red) no hoop mode, (gray) 2000 Hz, (black) 500 Hz, (green) 300 Hz, (brown) 800 Hz, and (purple) 1250 Hz. Conclusion

We model a ball–bat collision by using Euler-Bernoulli equations for the bat and hysteresis curves for the baseball. By doing so, we reconcile the literature by emphasizing the role of the time-scale of the collision and how the ball ―sees‖ only a local region of the bat because of the finite speed of wave propagation. As a result, the sweet spot is farther out in our model than the rigid-body recoil model predicts.

We vary the input parameters and show that the effects are in line with intuition and key results in previous experimental work.

Finally, we show that aluminum bats have wider sweet spots than wooden bats.

We offer several suggestions for improvements and extensions:

?The ball is assumed to be non-rotating with head-on impact; rotating balls and off-center collisions excite torsional modes in the bat that we ignore and make the problem nonplanar.

?We neglect shear forces in the bat.

?Our analysis of hoop modes is rather cursory.

122 The UMAP Journal 31.2 (2010)

References

Adair, Robert Kemp. 1994. The Physics of Baseball. 2nd ed. New York: Harper-Collins.

Baseball Research Center, University of Massachusetts–Lowell. n.d. Highspeed

video of a baseball striking a flat plate at about 120 mph, taken at 30,000 frames/s. http://webusers.npl.illinois.edu/~a-nathan/

pob/video/BRC_baseball_30k.avi .

Brody, H. 1986. The sweet spot of a baseball bat. American Journal of Physics

54(7): 640–643. /link/?AJP/54/640/1 .

Cross, Rod. 1999. Impact of a ball with a bat or racket. American Journal of Physics 67(8): 692–702. /link/?AJP/67/692/1 .

Goldsmith,Werner. 1960. Impact. London, U.K.: Edward Arnold Publishers Ltd.

Graff, Karl F. 1975. Wave Motion in Elastic Solids. New York: Dover. Nathan, Alan M. 2000. Dynamics of the baseball–bat collision. American Journal of Physics 68(11): 979–990. /link/?AJP/ 68/979/1 .

. 2003. Characterizing the performance of baseball bats. American Journal of Physics 71 (2): 134–143. /link/?AJP/ 71/134/1 .

Russell, Daniel A. 2003. Vibrational modes of a baseball bat. http://paws. kettering.edu/~drussell/bats-new/batvibes.html .

Van Zandt, L.L.. 1992. The dynamical theory of the baseball bat. American Journal of Physics 60(2): 172–181. /link/?AJP/ 60/172/1 .

Team members Yang Mou, Rajib Quabili, and Peter Diao,

with advisor Robert Calderbank.

Judges’ Commentary 123

Judges’ Commentary:

The Outstanding Sweet Spot Papers Michael Tortorella

Rutgers University

Piscataway, NJ

mtortore@rci.rutgers.edu

Introduction

Apparently themarch of technology in MajorLeagueBaseball(MLB)ismore

of a crawl. The basic tools of baseball have not changed or been substantially modified for a long time. It would seem that the business goals of MLB are being adequately met with tools that are decades—if not centuries—old. In particular, the baseball bat is pretty much the same implement that it was when Abner Doubleday walked the earth. It is not often that a tool persists basically unchanged without some improvement being brought to bear. Some began to wonder what the properties of such a remarkable tool might possess.

A FewWords About the Problem

Like most problems in the Mathematical Contest in Modeling (MCM)!R , this problem was deliberately designed to be open-ended. In particular, the key phrase ―sweet spot‖ in the statement of the problem was not defined. This was fortunate because teams brought many definitions forward and this produced a richer experience not only for the teams but also for the judges. Some of the useful interpretations of ―sweet spot‖ included:

?the spot where a batted ball would travel farthest,

?the spot where the sensation of vibration in the batter‘s hands is minimized, ?the center of percussion,

?the location that produces the greatest batted ball speed, and

?the location where maximum energy is transferred to the ball.

TheUMAP Journal 31 (2) (2010) 123–128. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP.

124 The UMAP Journal 31.2 (2010)

Several other definitions or interpretations are easily found through even a cursory literature search. Teams that did not discover this were generally eliminated

in triage.

This observation compels us to consider also the relationships among problem statements, the Internet, and competing teams. It is extremely difficult, if

not impossible, to imagine a problem that would be suitable for the MCM and for which there has been no prior art. Truly original problems, ones at which the MCM teams are the first to have a go, must be rare. Sometimes, we see a situation in which the proposed problem—while in its most general form is familiar—may be novel as an application to a particular situation which has received scant prior attention.

An example of this kind of problem is the Tollbooth Problem of the 2005 MCM.1 While it would have been nearly impossible to find prior art applied specifically to the situation presented (namely, to barrier tolls on the Garden State Parkway in New Jersey), standard methods of queueing theory and dimensional

analysis could be brought to bear.

In general, the Internet provides teams with a powerful resource to help find what, if anything, has been done on a topic before. This is a recent development

that was not in play even a decade ago. Teams, coaches, and judges need to find a fair way of coping with this changed situation:

?On one end of the spectrum, it is not reasonable for a team to simply copy what they find on the Internet and submit this as their solution. No one learns any modeling from this.

?At the other end of the spectrum, teams may develop entirely new models that do not resemble anything found online. While this may be desirable, it is probably unusual.

Most submitted papers will fall somewhere between these extremes. The

challenge for everyone is to make theMCMa learning experience for the teams and an enriching one for the judges in the face of this new technology. Ageneral

discussion of this issue is beyond the scope of this article; so suffice it to say that

for this particular problem, the presence on the Internet of substantial material on solving the problem was appropriately treated by the winning teams. Teams who simply copied material from sources without adding any value of their own were not considered winning teams.

Interpretation Is Important

As always, interpretation is a key to success in modeling problems. Teams must recognize that in addition to their usual semantic or prose usage, key words in the problem statement must also be given a mathematical meaning in 1Editor‘s Note: Dr. Tortorella was the author of both the Tollbooth Problem, as well as the Sweet Spot Problem that he comments on here as a contest judge.

Judges’ Commentary 125

the context of a model. Successful papers began by providing definitions of at least two possible interpretations of ―sweet spot.‖ Once that is accomplished, it begins to be possible to talk in quantitative terms about how to determine such a sweet spot (or spots).

Modeling

Whatever model is chosen, it is necessary to produce an expression relating the sweet spot (SS) to physical parameters of the batter–bat–ball system. For instance, the Zhejiang University team investigated the SS as the location on the bat where the batted ball speed is greatest upon leaving the bat. Then the team developed a relationship between this definition and

?impact location,

?ball mass,

?ball initial speed,

?the moment of inertia of bat,

?the swinging bat speed, and

?the coefficient of restitution (COR) of the ball.

This team made good use of clear illustrations to help the reader grasp the work involved.

The Huazhong University of Science and Technology team made use of a weighted average of two SS criteria and found, not surprisingly, that the

resulting location of SS is a compromise between batter comfort and battedball departure speed. This is a nice example of how a team amplified results available on the Internet to generate new insights. The Princeton University team defined SS as the location on the bat that imparts maximum outgoing velocity to the batted ball.

An interesting comment on the choice of SS criteria is that most teams did not explicitly connect their choice to the strategy of the game. That is, the criteria

for the SS should be related in some explicit way to the result that the batter is trying to achieve, namely, to score runs. From this point of view, criteria such as ―maximum batter comfort‖ are perhaps secondary desirable features but

are

probably not the most important ones in the short term. It may be more suitable to choose criteria such as maximum batted-ball departure velocity, maximum location controllability, or something that is directly related to producing runs. Most teams accepted their criteria as being implicitly connected with results of the game, but few if any discussed this point—clearly a key point!—at all. The Outstanding teams were able to develop clear equations, based on the dynamics of the batter–bat–ball system, for the location of the SS. Most teams followed this approach, but the Outstanding papers were especially clearly reasoned and made good use of illustrations to help clarify points for the reader.

126 The UMAP Journal 31.2 (2010)

The contest weekend is a busy weekend; but those papers that took the time to pay attention to helping the reader with good organization, clear writing, and attractive presentation in their report received more favorable reviews. Of course, these desirable features cannot make up for a weak solution; but lack of

such features can easily cover up a good solution and make it harder to discern.

This is not a trivial concern, because triage reads are very fast and it would be distressing if a triage judge were to pass over a worthwhile paper because its presentation made it hard for the judge to discern its solution quality.

Some teams, including the Huazhong University of Science and Technology team, expressed their results very precisely (for example, the SS is 20.15cmfrom

the end of the bat). This may be more than is required, partly because of the limited precision of real-world measuring instruments, but also because teams should be aware that stating a result in such a fashion compels a sensitivity analysis for this quantity. The Outstanding teams determined that even though a location for the SS could be calculated, the point of impact of the ball with the bat could vary somewhat from the SS without too much change in the value of the objective function (e.g., the batted-ball departure velocity). The Huazhong University of Science and Technology team, as well as several other teams, defined a ―Sweet Zone‖ to capture the notions that

?different SS criteria lead to different locations on the bat, and

?most of the objective functions employed are not very sensitive to the specific location of the bat-ball impact.

Conclusion

Studying these Outstanding papers offers good lessons in preparing entries for the MCM. Here are a few:

?Make your paper easy to read. That means at the very least:

– number the pages and the equations,

– check your spelling and grammar,

– provide a table of contents, and

– double-space the text (or at least use a font size large enough for easy readability).

All four Outstanding papers did a good job with this.

?Good organization will not make up for poor results, but poor organization

can easily overwhelm good results—and make them hard to dig out. It can help to organize the paper into sections corresponding to the requirements in the problem statement and into subsections corresponding to parts of the problem. The teams from the U.S. Military Academy and Princeton University did an especially good job with this.

Judges’ Commentary 127

?Define all terms that a reader might find ambiguous. In particular, any term used in the model that also has a common prose meaning should be carefully considered.

?Complete all the requirements of the problem. If the problem statement says that certain broad topics are required, begin by making an outline based on those requirements. Typical examples are statement and discussion of assumptions, strengths and weaknesses of model, and sensitivity analysis. ?Read the problem statement carefully, looking for key words implying

actions: ―design,‖ ―analyze,‖―compare,‖andother imperative verbs. These are keys to the work that you need to do and to the sections that your paper ought to contain.

?When you do “strengths and weaknesses” or sensitivity analysis, go back to your list of assumptions and make sure that each one is addressed.

This is your own built-in checklist aiding completeness; use it.

?Your summary should state the results that you obtained, not just what

you did. Keeping the reader in suspense is a good technique in a novel, but it simply frustrates judges who typically read dozens of papers in a weekend. The Princeton University paper has an excellent summary: crisp, concise, and thorough.

?Use high-quality references. Papers in peer-reviewed journals, books, and

governmentWebsites are preferred to individuals‘Websites. Note also that it is not sufficient to copy, summarize, or otherwise recast existing literature; judges want to see your ideas. It‘s okay to build on the literature, but there must be an obvious contribution from the team.

?Verify as much as you can. For example, the physical characteristics of baseballs and baseball bats are readily verifiable. Make whatever sanity

checks are possible: Is your answer for the departing ball‘s speed faster than the speed of light? If so, should it be?

?Finally, an Outstanding paper usually does more than is asked. For example, the team from the U.S. Military Academy (and many other teams that lacked other qualities needed to be Outstanding) studied two different models for the problem and compared the results from each approach; the reasonably good agreement that they obtained showed that either – they were on the right track; or

– they were victims of very bad luck, in that both of the methods gave nearly the same bad answers!

128 The UMAP Journal 31.2 (2010)

About the Author

Mike Tortorella isVisiting Professor at RUTCOR,

the Rutgers Center for Operations Research at

Rutgers, the State University of New Jersey, and

Managing Director of Assured Networks, LLC.

He retired from Bell Laboratories as a Distinguished

Member of the Technical Staff after 26

years of service. He holds the Ph.D. degree in

mathematics from Purdue University. His current

interests include stochastic flow networks,

networkresiliencyandcritical infrastructure protection,

and stochastic processes in reliabilityand

performance modeling. Mike has been a judge at theMCMsince 1993 and particularly

enjoys theMCMproblems that have a practical flavor of mathematical

analysis of social policy. Mike enjoys amateur radio, playing the piano, and cycling.

Centroids, Clusters, and Crime 129

Centroids, Clusters, and Crime:

Anchoring the Geographic Profiles of

Serial Criminals

Anil S. Damle

Colin G.West

Eric J. Benzel

University of Colorado–Boulder

Boulder, CO

Advisor: Anne Dougherty

Abstract

A particularly challenging problem in crime prediction is modeling the

behavior of a serial killer. Since finding associations between the victims is difficult, we predict where the criminal will strike next, instead of whom.

Such predicting of a criminal‘s spatial patterns is called geographic profiling. Research shows that most violent serial criminals tend to commit crimes in a radial band around a central point: home, workplace, or other area of significance to the criminal‘s activities (for example, a part of town where prostitutes abound). These ―anchor points‖ provide the basis for our model. We assume that the entire domain of analysis is a potential crime spot, movement of the criminal is uninhibited, and the area in question is large enough to contain all possible strike points. We consider the domain a metric space on which predictive algorithms create spatial likelihoods. Additionally, we assume that the offender is a ―violent‖ serial criminal, since research suggests that serial burglars and arsonists are less likely to follow spatial patterns.

There are substantial differences between one anchor point and several. We treat the single-anchor-point case first, taking the spatial coordinates of the criminal‘s last strikes and the sequence of the crimes as inputs. Estimating the point to be the centroid of the previous crimes, we generate a ―likelihood crater,‖ where height corresponds to the likelihood of a future crime at that location. For the multiple-anchor-point case, we use a cluster-finding and sorting method: We identify groupings in the data and build a likelihood crater around the centroid of each. Each cluster is given weight according to recency and number of points. We test single point vs. multiple points by TheUMAPJournal 31 (2) (2010) 129–148. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 130 The UMAP Journal 31.2 (2010)

using the previous crimes to predict the most recent one and comparing with

its actual location.

We extract seven datasets from published research. We use four of the datasets in developing our model and examining its response to changes in sequence, geographic concentration, and total number of points. Then we evaluate our models by running blind on the remaining three datasets.

The results show a clear superiority for multiple anchor points.

Introduction

The literature on geographic patterns in serial crimes shows a strong patterning around an anchor point—a location of daily familiarity for the criminal. We build prediction schemes based on this underlying theory and produce a surface of likelihood values and a robust metric.

The first scheme finds a single anchor point using a center-of-mass

method; the second scheme assumes two to four anchor points and uses a cluster-finding algorithm to sort and group points. Both schemes use a statistical technique that we call cratering to predict future crime locations. Background

The arrest in 1981 (and subsequent conviction) of Peter Sutcliffe as the ―Yorkshire Ripper‖ marked a victory for Stuart Kind, a forensic biologist whose application of mathematical principles had successfully predicted where the Yorkshire Ripper lived.

Today, information-intensivemodels can be constructed using heat-map techniques to identify the hot spots for a specific type of crime, or to derive associations between the rate of criminal activity and attributes of a location (such as lighting, urbanization, etc.) [Boba 2005].

―Geographically profiling‖ the crimes of a single criminal has focused on locating the criminal‘s anchor points—locations (such as a home, workplace,

or a relative‘s house) at which he spends substantial amounts of time and to which he returns regularly between crimes.

Canter and Larkin [1993] proposed that a serial criminal‘s home (or

other anchor point) tends to be contained within a circle whose diameter is the line segment between the two farthest-apart crime locations; and this is true in the vast majority of cases [Kocsis and Irwin 1997]. Canter et al.

[2000] found that for serial murders, generalizations of such techniques on average reduce the area to be searched by nearly a factor of 10.

By contrast, forecasting where a criminal will strike next has not been explored deeply [Rossmo 1999]. Paulsen and Robinson [2009] observe that

for many U.S. police departments there are substantial practical, ethical, and legal issues involved in collecting the data for a detailed mapping Centroids, Clusters, and Crime 131

of criminal tendencies, with the result that only 16% of them employ a

computerized mapping technique.

Our treatment of the problem will employ anchor-point-finding algorithm. We generate likelihood surfaces that act as a prioritization scheme for regions to monitor, patrol, or search.

Assumptions

Domain is Approximately Urban

We use the word ―urban‖ to denote features of an urbanized area that simplify our treatment: The entire domain is a potential crime spot, the

movement of the criminal is completely unconstrained, and the area is large enough to contain all possible strike points. It is important to note, however, that even for serial crime committed in suburbs, villages, or spread between towns, the urbanization condition holds on the subset of the map in which crimes are regularly committed. To see this, consider the three urbanization conditions separately:

?Entire domain is a potential crime spot. Every neighborhood contains a possible crime location. Such an assumption is made by nearly all geographic profiling techniques [Canter et al. 2000; Rossmo 1999] It is obvious that every domain will violate these conditions to some extent: All but the most inventive serial killers, for example, will not commit a crime in the middle of a lake, or in the uninhabited farmland between small towns. Nevertheless, this observation simply requires that the output of the model be interpreted intelligently. In other words, while we assume for simplicity that the entire map is a potential target, police officers interpreting the results can easily ignore any predictions we make which fall into an obvious ―dead zone.‖

?Criminal’smovementis unconstrained. Because of the difficulty of finding

real-world distance data, we invoke the ―Manhattan assumption‖:

There are enough streets and sidewalks in a sufficiently grid-like pattern that movements along real-world movement routes is the same as

―straight-line‖ movement in a space discretized into city blocks [Rossmo 1999]. Kent [2006] demonstrated that across several types of serial crime, the Euclidean and Manhattan distances are essentially interchangeable in predicting anchor points.

?Domain contains all possible strike points. This condition says that the two conditions above hold on a sufficiently large area.

Taken together, these three conditions describe the region of interest as a metric space in which

?The subset of potential targets is dense,

132 The UMAP Journal 31.2 (2010)

?the metric is the L2 norm, and

?the space is ―complete‖: Sequences of crimes do not lead to predictions of crimes outside the space.

Violent Serial Crimes by a Single Offender

?Focus on violent crimes. Geographic profiling is most successful for murders and rapes, with the average anchor-point prediction algorithm being 30% less effective for criminals who are serial burglars or arsonists

[Canter et al. 2000; Rossmo 1999].

?Serial crimes. We take serial killing (or violent crime) as involving ―three or more people over a period of 30 or more days, with a significant cooling-off period between‖ [Holmes and Holmes 1998].

?Single offender.

Spatial Focus

Use of temporal data is problematic. Time data can be inaccurate. Also, while research has found cyclical patterns within the time between crimes, these patterns don‘t associate directly to predicting the next geographic location. What is useful is general trends in spatial movement over an ordering of the locations. We hence ignore specific time data in crime sets except for ordering of the crime sequence.

Developing a Serial Crime Test Set Existing Crime Sets

Researchers have compiled databases of serial crimes for their own use: Rossmo‘s FBI and SFU databases [Rossmo 1999], LeBeau‘s San Diego Rape

Case dataset [LeBeau 1992], and Canter‘s Baltimore crime set [Canter et al.

2000]. Each of these databases was developed with specific methods of integrity and specific source locations. These proprietary databases are not available to us, so we are faced with two options: simulate serial criminal data or find an indirect way of using the private data.

The Problem with Simulation

Simulation might seem like an attractive solution to the lack of data. However, utterly random crime-site generation would contradict the underlying

assumption of a spatial pattern to serial crimes, while generating

sites according to an underlying distribution would prejudge the pattern! Actual data must be used if there is to be any confidence in the model. Centroids, Clusters, and Crime 133

An Alternative: Pixel Point Analysis

Instead,we―mine‖the available data, inRossmo[1995]andin the spatial

analysis of journey-to-crime patterns in serial rape cases in LeBeau [1992]. LeBeau depicts the data as scatterplots, which we rasterize and re-render with scaling. Figure 1 shows an example of this process, which we applied to seven criminals‘ data (four killers, three rapists). The rape sequences have an explicit ordering, while the murder sequences are unordered. Figure 1. Re-rendering of scatterplot in LeBeau [1992] for Offender B.

Metrics of Success

A successful model must outperform random predictions.

The Effectiveness Multiplier

We assume that police effectiveness is proportional to resources allocated, and that the resources allocated at a location are proportional to the

likelihood given by the model. We say that one model outperforms another if it recommends allocating more police resources to where the next crime is actually committed.

134 The UMAP Journal 31.2 (2010)

We assess how much one model outperforms another by the effectiveness multiplier κ, the ratio of resources allocated at the crime point under each model. Alternatively, κis the ratio of the percentage of total department resources allocated to the point. Since the total resources are the same in both models, we can evaluate κsimply as

κ= Z1(CrimePoint)

Z2(CrimePoint)

whereZi is the likelihood function of model i andCrimePoint is the actual location of the next crime.

A randomly guessing algorithm will have a uniform distribution over

locations and hence a flat likelihood plot. We compare our model to such a random guess by computing a standard effectiveness multiplier κs: κs = Zour model(CrimePoint)

Zflat(CrimePoint)

A value of 1 would indicate that the model was no better than a random guess, and a value less than 1 would indicate that the model misled the police.

Robustness of the Metric

We also want to compare the success of our algorithm across multiple datasets. It is legitimate to compare κs values between two datasets only if they have the same ratio of the killer‘s active region to the total area. The size of the killer‘s active region cannot be precisely known; however, we employ a standard technique to make this condition approximately true. According to Canter and Larkin [1993] and Paulsen [2005], in more than 90% of cases all future crimes fall within a square whose side length is the maximum distance between previous crime points and whose center is the centroid of the data. For each of our datasets, we construct such a square and then multiply its side length by 3, thereby creating an overall search area nearly 9 times as large as the criminal‘s active area. This ratio is nearly

constant for all datasets, allowing us to compare effectiveness multipliers. Two Schemes for Spatial Prediction

Journey-to-crime research for violent serial crimes strongly suggests that serial crime is patterned around a criminal‘s home, workplace, or other place of daily activity [Godwin and Rosen 2005; Holmes and Holmes 1998; Kocsis and Irwin 1997; Rossmo 1999; Snook et al. 2005]; so researchers have developed and evaluated methods of finding such a crime centroid Centroids, Clusters, and Crime 135

and investigated it as an anchor point in the criminal‘s activity. In most research, this anchor point is the serial criminal‘s home. This method has been tested and found to reduce the necessary search area by a factor of 10.

We develop two schemes, one for a single anchor point and the other for multiple anchor points.

Single Anchor Point: Centroid Method Figure 2 shows our algorithm to predict likely crime locations using a single anchor point.

Create Search Domain

Find Centroid of

Crime Sites

Build Likelihood

Crater

Adjust for

Temporal Trends

Weight by

Previous Crimes

Output Likelihoods

Figure 2. Flow chart for centroid method.

Algorithm

Create Search Domain

We construct the smallest square that contains every previous crime,

then scale up each dimension by a factor of 3. This ensures that all of our fundamental assumptions about the underlying domain are satisfied, and the consistent scale factor of 3 allows us to compare the algorithm between datasets.

136 The UMAP Journal 31.2 (2010)

Find Centroid of Crime Sites

The anchor point is the average of the n crime coordinates (xi, yi).

Building a Likelihood Crater

We predict future crime locations using the ―journey-to-crime‖ model, which says that the criminal‘s spatial pattern of crime around an anchor point does not change. A rough first prediction might be to draw a large

shape (circle, square, polygon, etc.) around this anchor point based on the largest distance from a crime point to the anchor point; such a method is incredibly ineffective compared to the largest-circle guess thatwedescribed earlier [Paulsen 2005].

We instead use a cratering technique first described by Rossmo [1999]. The two-dimensional crime points xi are mapped to their radius from the anchor point ai, that is, we have f : xi →ri, where f(xi) = kxi ?aik2 (a

shifted modulus). The set ri is then used to generate a crater around the anchor point.

There are two dominating theories for the pattern serial crimes follow around an anchor point:

?There is a buffer zone around the anchor point. The criminal commits crimes in an annulus centered at the anchor point [Kocsisand Irwin 1997]. This theory is often modeled using the positive portion of a Gaussian curve with parameters the mean and the variance of the {ri}.

?Crimes follow a decaying exponential pattern from the anchor point.

Both theories have been substantiated by journey-to-crime research. We seek a distribution that would model either theory, depending on the pattern in the crime sequence. For this we turn to the flexibility of the gamma distribution, which offers a ―shifted-Gaussian‖-like behavior when points lie farther away but a curve similar to a negative exponential when the parameters are small.

Define the random variable Xi to be the distance between the ith crime point and the anchor point r. We let each Xi have a gamma distribution with parameters k and θ: Xi ?Γ(k, θ), with probability density function (pdf)

f(x; k, θ) = θk

Γ(k) xk?1e?θx.

We assume independence of the Xi and use the maximum likelihood estimates

of the parameters k and θas calculated by the gamfit function in MatLab.

We then build the crater of likely crime locations using the resulting

distribution. For every point in the search region, we evaluate the pdf. We then normalize so that the volume under the likelihood surface is exactly 1. Centroids, Clusters, and Crime 137

Applying this method to the set of crime locations of Peter Sutcliffe, the ―Yorkshire Ripper,‖ we get the heat map of Figure 3.

Figure 3. Heat map showing cratering technique applied to the crime sequence of Peter Sutcliffe. Adjust for Temporal Trends

We would like our prediction to account for any radial trend in time

(the criminal becoming more bold and committing a crime closer or further from home): An outward or inward trend in ri may suggest that the next crime will follow this trend [Kocsis and Irwin 1997]. We let ?X = X +4r, where 4r = rn ?rn?1. The new random variable ?X gives our intended temporal adjustment in expected value:

E[?X ] = E[X +4r] = E[X] +4r.

Results and Analysis

To evaluate our method, we feed it data from three serial-rape sprees.

In each test case, we remove the data point for the final crime and produce a likelihood surface Z(x, y). We then estimate the location of the final crime and compute the standard effectiveness multiplier κs.

138 The UMAP Journal 31.2 (2010)

Offender C

Our first test dataset, for Offender C, is a comparative success (Figure 4). With κs ≈12, it is a full order of magnitude better to distribute police resources using this model instead of distributing them uniformly. a. Heat map. b. Surface plot.

Figure 4. Offender C predictions of location of final crime, from centroid model of previous crimes. The next-crime estimate falls satisfyingly near the isoline of maximum height; but there 120 grid squares are rated greater or equal in likelihood, meaning 0.3 km2 must be patrolled at the same or greater intensity. This area is small in an absolute sense; but it is comparatively large given that the vast majority of the crimes in this case were committed within an area of 1 km2.

WithΔr = ?0.276, the temporal corrections in this distribution are negligible; our projection is simply a radially symmetric fit to the geographic

dispersion of previous crimes. The surface plot also shows the steepness of the ―inside‖ of the crater, as the geographic distribution apparently suggests a small buffer zone around the centroid.

Offender B

Our second test dataset, for Offender B (see Figure 5 ), is similarly successful,

with κs ≈12.

Offender A

For Offender A, we find a clear example of how our model can fail. The last crime (see Figure 6) is one of two substantial outliers, and in fact, with a

standard effectiveness multiplier of κs ≈0.4, our model is less helpful than random guessing. However, the majority of previous crimes are still well described by the model, so the assumption of an anchor point somewhere Centroids, Clusters, and Crime 139

within the crater region does not appear to have been a poor one. Some scheme, whim, or outside influence caused the criminal to deviate from his previous pattern.

a. Heat map. b. Surface plot.

Figure 5. Offender B predictions of location of final crime, from centroid model of previous crimes. a. Heat map. b. Surface plot.

Figure 6. OffenderApredictions of location of final crime, from centroid model of previous crimes. Multiple Anchor Points: Cluster Method Our second method explicitly assumes at least two anchor points (for example, a home and a workplace) and treats each as the centroid of its own

140 The UMAP Journal 31.2 (2010)

local cluster of crimes. This method requires determining an appropriate number of clusters, which we derive from the locations of the previous crimes.

Algorithm

The basis of this algorithm is a hierarchical clustering scheme [Jain,

Murty, and Flynn 1999]. Once clusters are found, the previous algorithm is applied at each cluster centroid.

Finding Clusters in Crime Sequences

We force a minimum of 2 clusters and a maximum of 4. The clustering algorithm is accomplished in a 3-step process.

1. Compute the distances between all crime locations, using the Euclidean distance.

2. Organize the distances into a hierarchical cluster tree, represented by a dendrogram. The cluster tree of data points P1, . . . , PN is built up by first assuming that each data point is its own cluster. The dendrogram for Offender B is shown in Figure 7.

Figure 7. Dendrogram for Offender B.

Centroids, Clusters, and Crime 141

3. Merge the two clusters that are the closest (in distance between their centroids),

and continue such merging until the desired number of clusters

is reached. These cluster merges are plotted as the horizontal lines in the dendrogram, and their height is based on the distance between merged clusters at the time of merging.

To determine the optimal number of clusters, we use the notion of

silhouettes

[Rousseeuw 1987]. We denote by a(Pi) the average distance from Pi to all other points in its cluster and by b(Pi, k) the average distance from Pi to points in a different cluster Ck. Then the silhouette of Pi is

s(Pi) =

Σ

min

k|Pi /∈Ck

b(Pi, k)

Π

?a(Pi)

max

μ

a(Pi), min

k|Pi /∈Ck

b(Pi, k).

?(1)

The silhouette s can take values in [?1, 1]: The closer s(Pi) is to 1, the better Pi fits into its current cluster; and the closer s(Pi) is to ?1, the worse it fits within its current cluster.

To optimize the number of clusters, we compute the clusterings for 2, 3, and 4 clusters. Then for each number of clusters, we compute the average silhouette value across every point that is not the only point in a cluster. (We ignore silhouette values at single-point clusters because otherwise such

clusters influence the average in an undesirable way.) We then find the maximum of the three average silhouette values. For Offender B, we found average silhouette values of 0.52, 0.50, and 0.69 for 2, 3, and 4 clusters. So in this case, we go for four clusters. The cluster groupings computed by the algorithm are shown in Figure 8. Because the average silhouette value tends to increase with the number of clusters, we cap the possible number of clusters at 4.

Cluster Loop Algorithm

We compute the likelihood surface for the centroid of each cluster. If a cluster contains a single point, we do not assume that this cluster represents an anchor point; instead, we treat this point as an outlier. We use a Gaussian distribution centered at the point as the likelihood surface, with mean the expected value of the gamma distribution placed over every anchor point of a cluster that has more than one point.

Combining Cluster Predictions: Temporal and SizeWeighting Using the separate likelihood surfaces computed for each cluster, we

create our final surface as a normalized linear combination of the individual surfaces, using weights for the number of points in the cluster (to weight 142 The UMAP Journal 31.2 (2010)

Figure 8. Offender B crime points sorted into 4 clusters; the clusters are colored differently and separated by virtual vertical lines into 3, 6, 3, and 3 locations.

more-common locations) and for the average temporal index of the events in the cluster (to weight more-recent clusters).

Results and Analysis

The three test datasets conveniently display the cluster method‘s superior adaptability.

?Offender C: The highly-localized nature of the data points in Figure 9 means there is little difference between the centroid-method results and the cluster-method results. The only difference is that the cluster method identifies the point directly below the centroid as a cluster of a single point (an outlier) and therefore excludes it from the computation of the larger cluster‘s centroid (a slight Gaussian contribution from this point‘s ―own‖ cluster can be seen in the surface plot). This has the effect of slightly reducing the variance and therefore narrowing the fit function; consequently, the standard effectiveness multiplier rises slightly, from about 12 to almost 16.

?Offender B: By contrast, Figure 10 shows the cluster method operating at the other edge of its range, as the silhouette-optimization routine produces four clusters. It might appear that the centroid method

outperforms

the cluster algorithm for this dataset; after all, the actual crime

point no longer appears in the band of maximum likelihood. This is true and intentional, since the model weights the largest cluster most strongly Centroids, Clusters, and Crime 143

a. Heat map. b. Surface plot.

Figure 9. Offender C predictions of location of final crime, from cluster model of previous crimes. a. Heat map. b. Surface plot.

Figure 10. Offender B predictions of location of final crime, from cluster model of previous crimes. a. Heat map. b. Surface plot.

Figure 11. OffenderA predictions of location of final crime, from cluster model of previous crimes. 144 The UMAP Journal 31.2 (2010)

and the ―freshest‖ cluster next-most. Nevertheless, while not accurately predicting that the offender returns to an earlier activity zones, the cluster method still outperforms the centroid method with a κs ≈23. This

is because the craters generated by the cluster method are sharper and taller for this dataset, so fewer resources are ―wasted‖ at high-likelihood areas where no crime is committed.

?Offender A: Unsurprisingly, the cluster model fares no better than the centroid method (Figure 11). Since the outlier points are excluded from the centroid calculation for the larger cluster, the model bets even more aggressively on this cluster, with a resulting κs ≈0.

Combining the Schemes

Based on further work not shown in this briefer version of our contest paper, we developed a combined method to decide for a given situation whether the centroid method or the cluster method is better, based on calculating

running means of the effectiveness multipliers of the two methods as we predict each of the crime locations from the previous ones. Our combined method would use the clustering algorithm for all three

Offenders A, B, and C. One would have to have a a highly-cohesive single cluster of data with no outliers in order for the centroid method to ever prevail. This is as it should be, since even when there appears to be only one true anchor point, the cluster method can reject up to three statistical outliers before computing the centroid, which capability should in general improve the fits and consequently improve the results.

The Model vs. Random Guess, Intuitive Cops, etc.

Although our scant datasets do not allow anything conclusive, our

model is a strong candidate over other alternatives, for several reasons: ?The predictions are based on the assumption of trends in serial crime behavior which have been tested on large sets of real-world data [Canter et al. 2000; Kocsis and Irwin 1997; Paulsen and Robinson 2009]. ?Similar mathematical techniques are used in the anchor-point estimation schemes currently employed, which consistently outperform random guesses when tested across data samples.

?The model is successful in the two of the three real-life datasets on which we tested it.

?Several crimes in each dataset can be predicted well, even in the dataset where our model fails to predict the final, outlier crime point—i.e., in a dataset of 16 crimes, we are also often able to predict the 15th crime Centroids, Clusters, and Crime 145

using the preceding 14, the 14th using the preceding 13, etc., all with

more success than a random guess.

We do not claim that the model will do better than a police department in assigning resources based on knowledge of the area, a sense of patterning

in the offender‘s crimes, and any ―gut feelings‖ developed about the

offender‘s psychology, based on previous experience in law enforcement. Additionally, research suggests that with a little informal training, any

layperson can perform nearly as well as anchor-point-prediction algorithms in guessing a criminal‘shomelocation [Snook, Taylor, and Bennell 2004]. As a result, one might well expect an ―intuitive cop‖ to outperform the model overall, by approximating its mathematical strengths through intelligent estimation plus bringing a breadth of knowledge and experience to bear. Executive Summary

Overview: Strengths andWeaknesses of the Model

We present a model of where a violent serial criminal will strike next,

based on the locations and times of previous crimes. Our algorithm creates a color-coded map of the area surrounding the criminal‘s previous strikes, with the color at each point indicating the likelihood of a strike there. The model has several key strengths:

?The model contains no arbitrary parameters. In other words, most aspects

of the model are determined simply by trends observed in datasets about many serial criminals.

?The model can estimate the level of confidence in its predictions. Our model first checks how well it would have predicted the criminal‘s previous crimes, in order to provide an estimate of how well it can predict

future crimes.

?The model understands that police have limited resources. In particular,

the confidence level described above becomes large if we are making good predictions but will shrink again if our predicted areas become so large as to become unhelpful.

At the same time, our model contains some fundamental limitations: ?The model is applicable only to violent serial criminals. We claim applicability only for serial killers and rapists, since our research shows that serial burglars and arsonists are more unpredictable and influenced by non-geographic factors.

?The model cannot predict when a criminal will strike. While we

consider

the order of previous crimes in order to predict locations, we do

not predict a strike time.

146 The UMAP Journal 31.2 (2010)

?The model cannot make use of underlying map data. To maintain

generality, we do not make any assumptions about the underlying physical geography. A human being must interpret the output (for example, choosing to ignore a prediction in the middle of a lake).

?The model has not been validated on a large set of empirical data. Sizable sets of data on serial criminals are not widely available.

In addition, the standard warnings that would apply to any geographic profiling scheme apply: The output should not be treated as a single prediction

but rather as a tool to help prioritize areas of focus. It is designed to do well on average but may fail in outlier cases. And to implement it reliably, it must be paired with a human assessment. Please note also that models for predicting the offender‘s ―home base‖ are much more well researched and in general will be more accurate than any algorithm claiming to predict the next strike point. A police department should choose on a case-by-case basis which model type to use.

InternalWorkings of the Model

Inputs

Our model requires the coordinate locations of a serial criminal‘s previous offenses, as well as the order in which these crimes were committed. Assumptions

1. The criminal will tend to strike at locations around one or more anchor points (often, the criminal‘s home).

2. Around this anchor point, there may be a ―buffer zone‖ within which he will not strike.

3. If the criminal has multiple anchor points, the regions around those from which he has struck most often or most recently are more likely.

Method

Thealgorithmimplementstwodifferent models, andthen decideswhich is better.

?The first method assumes that the criminal has a single anchor point and builds likelihood regions around the anchor point based on the distribution of his past crimes.

?The second method assumes multiple anchor points, calculates the best number of anchor points to use, determines likelihood around each point

individually, andweights the area aroundeachbythe criminal‘sapparent preferences.

Centroids, Clusters, and Crime 147

Finally, the algorithm tests both models to see how well they would have predicted the previous crimes and uses the model with the better track record.

Summary and Recommendations

While our model needs more real-world testing, its strong theoretical

basis, self-evaluation scheme, and awareness of practical considerations makeit agoodoption for a police departmentlooking to forecast a criminal‘s next strike. Combining its results with the intuition of a human being will maximize its utility.

References

Boba, Rachel. 2005. Crime Analysis and Crime Mapping. Thousand Oaks, CA:

Sage Publications.

Canter, David, and Paul Larkin. 1993. The environmental range of serial rapists. Journal of Environmental Psychology 13: 63–63.

Canter, David, Toby Coffey, Malcolm Huntley, and Christopher Missen. 2000. Predicting serial killers‘homebase using a decision support system. Journal of Quantitative Criminology 16(4): 457–478.

Godwin, Maurice, and Fred Rosen. 2005. Tracker: Hunting Down Serial Killers. Philadelphia, PA: Running Press.

Holmes, Ronald M., and Stephen P. Holmes. 1998. Contemporary Perspectives

on Serial Murder. Thousand Oaks, CA: Sage Publications.

Jain, A.K., M.N. Murty, and P.J. Flynn. 1999. Data clustering: A review. ACM Computing Surveys 31(3): 264–323.

Kent, Joshua David. 2006. Using functional distance measures when calibrating

journey-to-crime distance decay algorithms. Master‘s thesis,

Louisiana State University. http://etd.lsu.edu/docs/available/

etd-1103103-095701/ .

Kocsis, R.N., and H.J. Irwin. 1997. An analysis of spatial patterns in serial rape, arson, andburglary: Theutility of the circle theory of environmental range for psychological profiling. Psychiatry, Psychology and Law 4(2): 195–206.

LeBeau, James L. 1992. Four case studies illustrating the spatial-temporal analysis of serial rapists. Police Studies 15: 124–145.

Minka, Thomas P. 2002. Estimating a Gamma distribution.

http://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.

142.7635&rep=rep1&type=pdf .

148 The UMAP Journal 31.2 (2010)

Paulsen, Derek J. 2005. Predicting next event locations in a time sequence using advanced spatial prediction methods.

http://www.jdi.ucl.ac.uk/downloads/conferences/third_nat_

map_conf/derek_paulsen.pdf .

, and Matthew B. Robinson. 2009. Crime Mapping and Spatial Aspects of Crime. 2nd ed. Upper Saddle River, NJ: Prentice Hall.

Rossmo, D. Kim. 1995. Geographic profiling: Target patterns of serial murderers..

Ph.D. thesis, Simon Fraser University.

. 1998. Geographic profiling (NCIS Conference 1998). http://

/geopro/krossmo.pdf .

. 1999. Geographic Profiling. Boca Raton, FL: CRC Press.

Rousseeuw, Peter J. 1987. Silhouettes: A graphical aid to the interpretation and validation of cluster analysis. Journal of Computational

and Applied Mathematics 20(1): 53–65.

doi:10.1016/0377-0427(87)90125-7.

ftp://ftp.win.ua.ac.be/pub/preprints/87/Silgra87.pdf .

Snook, Brent, Paul J. Taylor, and Craig Bennell. 2004. Geographic profiling: The fast, frugal, and accurate way. Applied Cognitive

Psychology 18(1): 105–121. http://www.mun.ca/psychology/brl/ publications/Snook12.PDF .

Snook, Brent, Richard M. Cullen, Andreas Mokros, and Stephan Harbort. 2005. Serial murderers‘ spatial decisions: Factors that influence crime location choice. Journal of Investigative Psychology and Offender Profiling 2(3): 147–164. http://www.mun.ca/psychology/brl/publications/ Snook11.pdf .

Advisor Anne Dougherty with team members Anil Damle, ColinWest, and Eric Benzel.

Judges’ Commentary 149

Judges’ Commentary:

The Outstanding Geographic

Profiling Papers

Marie Vanisko

Dept. of Mathematics, Engineering, and Computer Science

Carroll College

Helena, MT 59625

mvanisko@carroll.edu

Introduction

The stated problem this year dealt with the issue of geographical profiling in the investigation of serial criminals. International interest in this topic has led to numerous publications, many of which present mathematical models for analyzing the problems involved. Although it was entirely appropriate and expected that teams working on this problem would review the literature on the subject and learn from their review, teams that simply presented published schemes as their mathematical models fell far short of what was expected. The

judges looked for sparks of creativity and carefully explained mathematical model building with sensitivity analysis that went beyond what is found in the literature. This factor is what added value to a paper.

Documentation and Graphs

We observed a noticeable improvement in how references were identified and in the specific precision in documenting them within the papers. Considering

the numerous online resources available, proper documentation was an especially important factor in this year‘s problem.

Despite the improvement, many papers contained charts and graphs from Web sources with no documentation. All graphs and tables need labels and/or legends, and they should provide information about what is referred to in the paper. The best papers used graphs to help clarify their results and documented

trustworthy resources whenever used.

TheUMAP Journal 31 (2) (2010) 149–151. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 150 The UMAP Journal 31.2 (2010)

Assumptions

In many cases, teams made tacit assumptions about the criminals being considered but did not state or justify critical mathematical assumptions that were later used implicitly. Assumptions concerning probability distributions, anchor points, distances, units, mathematical procedures, and how to measure results were generally not discussed or justified.

Since this is a modeling contest, a lot of weight is put on whether or not the model could be used, with modification, in the real world. Also, clear writing and exposition is essential to motivate and explain assumptions and to derive and test models based on those assumptions.

Summary

The summary is of critical importance, especially in early judging. It should motivate the reader and be polished with a good synopsis of key results. For this problem, teams were asked to add to their one-page summary (which can have some technical details) also a two-page executive summary appropriate for the Chief of Police. Many teams seemed to assume that the Chief of Police would have impressive mathematical credentials.

The Problem and Its Analysis

Teams were asked to develop at least two different schemes for generating geographical profiles and then to develop a technique for combining the results of the different schemes in such a way as to generate a useful prediction for law

enforcement officers. Although the papers designated as Meritorious generally developed interesting schemes, very few papers did an adequate job of testing their results and doing sensitivity analysis.

Most papers dealt with issues associated with the serial criminal‘s home

base, usually referred to as the anchor point, and the buffer zone around that point within which the criminal is unlikely to commit crimes. Locations were identified using latitude and longitude and sometimes a time factor. Weights were frequently assigned to data points, sometimes taking more recent crimes into account more heavily and sometimes incorporating qualitative factors into the scheme. Teams used various metrics in describing ―distances‖ between the

anchor point and crime locations. Papers that rose to the top used well-defined metrics that were clearly explained. One cannot measure the reliability or validity of a model without clearly defined metrics.

Manyteamsmentionedthat therewasnot a lot of data withwhichthey could

validate their model, although they did find some specific location information that included from 13 to 20 crimes in a given series. Some teams used as their only example the Sutcliffe case cited in the problem. In almost all cases, teams Judges’ Commentary 151

used their model to predict the location of the final crime based on all of the previous locations for that criminal. They could easily have had many more data points with which to validate their models. For example, if 13 crime

locations were available, they could have used the first n locations to predict the location of crime n + 1, for each n = 7, . . . , 12. The judges agreed that this problem did not lend itself to validation by simulation, as many other problems do.

In describing the reliability of predicted results for proposed models, it

was sometimes difficult to determine precisely how teams had arrived at their results. Since the literature is full of models and even computer models, it would have been worthy if teams had solved a problem via one of these

methods

and used that as a baseline to compare the results of original models that they proposed. Not a single team did this to the judge‘s satisfaction. Judges do not generally look for computer code, but they definitely look for precise algorithms that produce results based on a given model.

Concluding Remarks

Mathematical modeling is an art. It is an art that requires considerable skill and practice in order to develop proficiency. The big problems that we face now and in the future will be solved in large part by those with the talent, the insight, and the will to model these real-world problems and continuously refine those models. Surely the issue of solving crimes involving serial killers is an important challenge that we face.

The judges are very proud of all participants in this Mathematical Contest in Modeling and we commend you for your hard work and dedication. About the Author

Marie Vanisko is a Mathematics Professor Emerita from Carroll College

in Helena, Montana, where she taught for more than 30 years. She was also a Visiting Professor at the U.S. MilitaryAcademyatWest Point and taught for five years at California State University Stanislaus. In both California and Montana, she directed MAA Tensor Foundation grants on mathematical modeling for high school girls. She also directs a mathematical modeling project for Montana

high school and college mathematics and science teachers through the Montana

Learning Center at Canyon Ferry, where she chairs the Board of Directors. She

has served as a judge for both the MCM and HiMCM.

152 The UMAP Journal 31.2 (2010)

Fusaro Paper Commentary 153

Judges’ Commentary:

The Fusaro Award for the

Geographic Profiling Problem

Marie Vanisko

Dept. of Mathematics, Engineering, and Computer Science

Carroll College

Helena, MT 59625

mvanisko@carroll.edu

Peter Anspach

National Security Agency

Ft. Meade, MD

anspach@aol.com

Introduction

MCM Founding Director Fusaro attributes the competition‘s popularity in part to the challenge of working on practical problems. ―Students

generally like a challenge and probably are attracted by the opportunity, for perhaps the first time in their mathematical lives, to work as a team on a realistic applied problem,‖ he says. The most important aspect of the MCMis the impact that it has on its participants and, as Fusaro puts it, ‖the confidence that this experience engenders.‖

The Ben Fusaro Award for the 2010 Geographic Profiling Problem went to a team from Duke University in Durham, NC. This solution paper was among the top Meritorious papers that this year received the designation of Finalist. It exemplified some outstanding characteristics:

?It presented a high-quality application of the complete modeling process. ?It demonstrated noteworthy originality and creativity in the modeling effort to solve the problem as given.

?It was well-written, in a clear expository style, making it a pleasure to read.

TheUMAP Journal 31 (2) (2010) 153–156. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 154 The UMAP Journal 31.2 (2010)

Criminology and Geographic Profiling Each team was asked to develop a method to aid in the investigations

of serial criminals. The team was to develop an approach that makes use of at least two different schemes and then combine those schemes to generate

a geographic profile that would be a useful prediction for law enforcement officers. The prediction was to provide some kind of estimate or guidance about possible locations of the next crime. based on the time and locations of the past crimes. In addition to the required one-page summary, teams had to write a two-page less-technical executive summary for the Chief of Police.

In doingWeb searches on this topic, teams found many publications and

many proposed models. While it was important to review the literature, to receive an Outstanding or Meritorious designation, teams had to address all the issues raised and come up with a solution that demonstrated their own creativity.

The Duke University Paper

Abstract (One-Page Summary)

The Duke team did an excellent job with their abstract. In one page, they motivated the reader and provided the reader with a good sense of what the team had accomplished. It gave an overview of everything from the assumptions, to the modeling and how it was done, to the testing of their models, and finally, to the analysis of the accuracy of their results and limitations of their models. It was well-written and a great example of what an abstract should be.

Executive Summary (for the Police Chief)

The executive summary too was well-written and gave an overview of the team‘s approach, acknowledging limitations of their models. However, it was a little too vague in providing a precise idea of exactly what

information would need to be collected and how to go about implementing the proposed models. Because the executive summary is a critical part of the requirements, this was part of what kept the Duke paper from being designated as Outstanding.

Assumptions

The team began with a brief survey of previous research on geographic profiling and used the information that they had gathered to decide what Fusaro Paper Commentary 155

assumptions seemed appropriate. As a result, their list of assumptions was well-founded. The team exemplified one of the most important aspects in mathematical modeling by demonstrating precisely how their assumptions were used in the development of their models and how the assumptions enabled them to determine parameters in their models.

The Models

The team‘s first model involved a geographic method that took into account not only the location of crimes but also population densities, crime rates, andselected psychologicalcharacteristics.Theyuseda

bivariateGaussian

probability function and numerous parameters associated with previous crime locations. Theydid a verygoodjob of showinghowtheir assumptions and previous crime scenes led to the computation of these parameters and then using these parameters to estimate the probability function to be

used in their model.

The team‘s second model involved a risk-intensity method and made

use of the geographic method but extended it to make different projections with different probabilities associated with each of those projections. Testing the Models

The Duke team was among the top papers, not only because of their well-based models, but because they tested their models—not with just one serial crime case, but with many cases. Their parameters allowed them to consider crimes other than murder, and they were able to examine how good their models were in several real-life situations. By analyzing their results, they were able to comment on the sensitivity and robustness of their

models. This was something that very few papers were able to do, and a very important step in the modeling process.

Recognizing Limitations of the Model

Recognizing the limitations of a model is an important last step in the completion of the modeling process. The teams recognized that their models

would fail if their assumptions did not hold—for example, if the criminal did not have a predictable pattern of movement.

References and Bibliography

The list of references consulted and used was sufficient, but specific

documentation of where those references were used appeared only for a few at the start of the paper. Precise documentation of references used is important throughout the paper.

156 The UMAP Journal 31.2 (2010)

Conclusion

The careful exposition in the development of the mathematical models made this paper one that the judges felt was worthy of the Finalist designation.

The team members are to be congratulated on their analysis, their

clarity, and for using the mathematics that they knew to create and justify their own model for the problem.

About the Authors

Marie Vanisko is a Mathematics Professor Emerita from Carroll College in Helena, Montana, where she taught for more than 30 years. She

was also a Visiting Professor at the U.S. Military Academy at West Point and taught for five years at California State University Stanislaus. In both California and Montana, she directed MAA Tensor Foundation grants on

mathematical modeling for high school girls. She also directs a

mathematical

modeling project for Montana high school and college mathematics and science teachers through the Montana Learning Center at Canyon Ferry, where she chairs the Board of Directors. She has served as a judge for both

the MCM and HiMCM.

Peter Anspach was born and raised in the Chicago area. He graduated from Amherst College, then went on to get a Ph.D. in Mathematics from the University of Chicago. After a post-doc at the University of Oklahoma, he joined the National Security Agency to work as a mathematician. Results of the 2010 ICM 157

Modeling Forum

Results of the 2010 Interdisciplinary Contest in Modeling

Chris Arney, ICM Co-Director

Dept. of Mathematical Sciences

U.S. Military Academy

West Point, NY 10996

David.Arney@usma.edu

Introduction

Atotal of 356 teams from four countries spent a weekend in February working in the 12th Interdisciplinary Contest inModeling (ICM)!R . This year‘s contest began on Thursday, Feb. 18, and ended on Monday, Feb. 22. During that time, teams of up to three undergraduate or high school students researched, modeled, analyzed, solved, wrote, and submitted their solutions to an openended

interdisciplinary modeling problem involving marine ecology. After

the weekend of challenging and productive work, the solution papers were sent to COMAP for judging. One of the top papers, which were judged to be Outstanding by the expert panel of judges, appears in this issue of The UMAP Journal.

COMAP‘s Interdisciplinary Contest in Modeling (ICM), along with it sibling, the Mathematical Contest in Modeling (MCM) !R , involves studentsworking in teams to model and analyze an open problem. Centering its educational philosophy on mathematical modeling, COMAP supports the use of mathematical

tools to explore real-world problems. It serves society by developing

students as problem solvers in order to become better informed and prepared as citizens, contributors, consumers, workers, and community leaders. The ICM andMCMare examples of COMAP‘s efforts in working towards its goals. This year‘s problem once again involved environmental sciences. The Great Pacific Ocean Garbage Patch Problem (or Marine Pollution Problem) was challenging

in its demand for teams to utilize many aspects of science, mathemat-

TheUMAP Journal 31 (2) (2010) 157–164. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 158 The UMAP Journal 30.2 (2010)

ics, and analysis in their modeling and problem solving. The problem required teams to understand the complexity of marine ecology and oceanography and to model that complexity to understand the effects of plastics building up in the Pacific Ocean Gyre. To accomplish their tasks, the teams had to consider many

difficult and complex issues. The problem also included the requirements of the ICM to use thorough analysis, research, creativity, and effective communication.

The author of the problem was marine biology researcher Miriam

Goldstein of the Scripps Institute of Oceanography.

All members of the 356 competing teams are to be congratulated for their excellent work and dedication to modeling and problem solving. The judges remarked that this year‘s problem was especially challenging and demanding in many aspects of modeling and problem solving.

Next year, we will continue the environmental science theme for the contest problem. Teams preparing for the 2011 contest should consider reviewing interdisciplinary topics in the area of environmental issues.

The Problem Statement:

The Great Pacific Ocean Garbage Patch Your ICM submission should consist of a 1 page Summary Sheet and a 10 page

report/solution for a total of 11 pages.

Recently, there has been considerable news coverage of the ―Great Pacific Ocean Garbage Patch.‖ See the following:

/2009/11/10/science/10patch.html?em /program/archives/200907314

/article/idUSTRE57R05E20090828

Based on recent scientific expeditions into the Pacific Ocean Gyre (a

convergence

zone where debris is accumulating), a wide variety of technical and

scientific problems associated with this debris mass are coming to light. While dumping waste into the ocean is not a new activity, what is new is the scientific community‘s realization that much of the debris (plastics, in particular)

is accumulating in high densities over a large area of the Pacific Ocean. The scientific community also is learning that this debris creates many potential threats to marine ecology, and as such, to human well-being. Those who study this accumulation often describe it as plastic soup or confetti. See

/news/2009/09/

photogalleries/pacific-garbage-patch-pictures/

This year‘s ICM problem addresses the complex issues stemming from the presence of ocean debris through the use of interdisciplinary modeling to help researchers (and ultimately, government policy-makers) to understand the severity, range, and potential global impact of the situation. As the modeling

advisors to the expedition, your job is to focus on one element of this Results of the 2010 ICM 159

debris problem and model and analyze its behavior, determining its potential effect on marine ecology and what government policies and practices should be implemented to ameliorate its negative effects. Be sure to consider needs for future scientific research and the economic aspects of the problem, and then

write a report to your expedition leader to summarize your findings and proposals

for solutions and needed policies and practices. Some of the possible issues/questions you could investigate with your model include:

1. What are the potential short- and long-term effects of the plastic on the ocean

environment? What kind of monitoring is required to track the impact on the marine ecosystem? Be sure to account for temporal and spatial variability. What are the associated resourcing requirements?

2. How can the extent, density, and distribution of the plastic in the gyre be best understood and described? What kind of monitoring plan is required to track the growth/decay/movement of the plastics, and what kind of resourcing is required to implement that plan?

3. What is the nature or mechanism of the photodegradation of the plastic and its composition as it enters the ocean and accumulates in the gyre? (We are amazed, for example, to find that the particles of degraded plastic tend to reach a similar size.)

4. Where does the plastic come from and what steps can be taken to control or reduce the risks associated with this situation? What are the economic costs and the economic benefits of controlling or ending the situation, and how do they compare? How much plastic is manufactured, discarded, and

recycled? How much of that is likely to go into the ocean? How much of that is likely to float?

5. Could similar situations develop in other areas in the oceans? What should we monitor and how? What is happening in the North Atlantic Gyre and in the Alaskan Gyre? Use your model to estimate the plastic density in the future in the southern gyres (South Atlantic, South Pacific).

6. What is the immediate impact of banning polystyrene takeout containers? (See http://bit.ly/5koJHB .) What is the impact over 10–50 years?

7. Your team can address any other scientific/technological issue associated with this situation, as long as modeling is an important component of your investigation and analysis.

To clarify your task: Focus on one critical aspect of this problem and model the behavior of the important matters or phenomena. Quantify the quantities that are of greatest present or future interest to the one aspect you choose to model and analyze. Your ICM report should be in the form of a 10-page team report to an expedition leader who has asked you to help her identify the relevant behaviors of the matters and phenomena under consideration, provide the analysis for impact of the behavior of those matters or phenomena, 160 The UMAP Journal 30.2 (2010)

and advise her on the government‘s potential to act on the problem to improve this situation before it worsens.

The following source materials [provided with the problem statement] contain some helpful data:

?the figure below;

?Moore et al. [2001];

?Rei and Tanimura [2007].

?

The References below suggest some papers to inform your model formulation and obtain more data.

Note: As a reminder, it is best to stick to the scientific literature, not the

media coverage, for your facts. The mainstream media coverage of this issue has been misleading in many cases. For further explanation, see:

http://seaplexscience.com/2009/11/13/millions-billionstrillions-

of-scientific-errors-in-the-nyt/ .

References

Committee on the Effectiveness of International and National Measures to Prevent

and Reduce Marine Debris and Its Impacts, National Research Council.

2008. Tackling Marine Debris in the 21st Century.Washington, DC: National Academies Press. www.nap.edu/catalog/12486.html .

Results of the 2010 ICM 161

Dameron, O.J., M. Parke, M.A. Albins, and R. Brainard. 2007. Marine debris accumulation in the Northwestern Hawaiian Islands: An examination of rates and processes. Marine Pollution Bulletin 54: 423–433.

Derraik, J.G.B. 2002. The pollution of the marine environment by plastic debris:

a review. Marine Pollution Bulletin 44: 842–852.

Matsumura, S., and K. Nasu. 1997. Distribution of floating debris in the north Pacific Ocean: Sighting surveys 1986–1991. In Marine Debris: Sources, Impact and Solutions, edited by J.M. Coe and D.B. Rogers, 15–24. New York: Springer.

Moore, C.J., S.L. Moore, M.K. Leecaster, and S.B.Weisberg. 2001.

Acomparison

of plastic and plankton in the North Pacific central gyre. Marine Pollution Bulletin 42: 1297–1300.

Pichel, W.G., J.H. Churnside, T.S. Veenstra, D.G. Foley, K.S. Friedman, R.E. Brainard, J.B. Nicoll, Q. Zheng, andP. Clemente-Colon. 2007. Marine debris collects within the North Pacific Subtropical Convergence Zone. Marine Pollution Bulletin 54: 1207–1211.

Robards, M.D., P. Gould, and J. Platt. 1997. The highest global concentrations and increased abundance of oceanic plastic debris in the North Pacific:

Evidence from seabirds. In Marine Debris: Sources, Impact and Solutions, edited by J.M. Coe and D.B. Rogers, 71–80. New York: Springer.

Venrick, E.L., T.W. Backman,W.C. Bartram, C.J. Platt, M.S. Thornhill, and R.E.

Yates. 1973. Man-made Objects on the Surface of the Central North Pacific Ocean. Nature 241: 271.

Yamashita, Rei, and Atsushi Tanimura. 2007. Floating plastic in the Kuroshio Current area, western North Pacific Ocean. Marine Pollution Bulletin 54: 485–488.

The Results

The 356 solution papers were coded atCOMAPheadquarters so that names and affiliations of the authors were unknown to the judges. Each paper was then read preliminarily by ―triage‖ judges at the U.S. Military Academy atWest Point, NY. At the triage stage, the summary, the model description, and overall organization are the primary elements in judging a paper. Final judging by a team of modelers, analysts, and subject-matter experts took place in late March.

The judges classified the 356 submitted papers as follows:

Honorable Successful

Outstanding Finalist Meritorious Mention Participant Total

Marine Pollution 4 6 45 120 181 356

162 The UMAP Journal 30.2 (2010)

One of the papers that the judges designated as Outstanding appear in this

special issue of The UMAP Journal, together with a commentary by the judges.

We list those Outstanding teams below.

Outstanding Teams

Institution and Advisor Team Members

―A New Method for Pollution Abatement:

Different Solutions to Different Types‖

Beijing Jiaotong University

Beijing, China

BingtuanWang

Yuxi Li

Lei Lu

Fandong Meng

―Shedding Light on Marine Pollution‖

Carroll College

Helena, MT

Philip Rose

Britttany Harris

Chase Peaselee

Kyle Perkins

―Quantitative Marine Debris Impacts and Evaluation

of Ocean System‖

Hangzhou Dianzi University

Hangzhou, China

Zheyong Qiu

Chenguang Fu

Longbin Shen

YaweiWen

―Size-Classified Plastic Concentration in the Ocean‖

Lawrence University

Appleton, WI

Stefan L. Debbert

Fangzhou Qiu

Lu Yu

Jian Gong

Awards and Contributions

Each participating ICM advisor and team member received a certificate

signed by the Contest Directors and the Head Judge. Additional awards were presented to the team from Carroll College (Montana) by the Institute for Operations

Research and the Management Sciences (INFORMS).

Judging

Contest Directors

Chris Arney, Dept. of Mathematical Sciences, U.S. Military Academy, West Point, NY

Joseph Myers, Computing Sciences Division, Army Research Office, Research Triangle Park, NC

Results of the 2010 ICM 163

Associate Director

Rodney Sturdivant, Dept. of Mathematical Sciences,

U.S. Military Academy,West Point, NY

Judges

John Kobza, Dept. of Industrial Engineering, Texas Tech University, Lubbock, TX

Miriam Goldberg, Scripps Institute of Oceanography, La Jolla, CA

Giora Proskurowski,Woods Hole Oceanographic Institution,Woods Hole,MA Kathleen Snook, COMAP Consultant, Bedford, MA

FrankWattenberg, Dept. of Mathematical Sciences, U.S. Military Academy, West Point, NY

Triage Judges

Dept. of Mathematical Sciences, U.S. Military Academy,West Point, NY: Darryl Ahner, Chris Arney, Amanda Beecher, Fr. Gabriel Costa, Chris Eastburg, Andy Glen, Andy Hall, Tina Hartley, Michael Harvey, Alex

Heidenberg, Craig Lennon, Chris Marks, Elizabeth Moseman, Elisha Peterson, Donovan Phillips, Elizabeth Russell, Libby Schott, Rodney Sturdivant, Edward Swim, Csilla Szabo, JoAnna Crixell Whitener, and Shaw

Yoshitani

Acknowledgments

We thank:

?INFORMS, the Institute for Operations Research and the Management Sciences,

for its support in judging and providing prizes for the INFORMS

winning team;

?IBM for its support for the contest;

?all theICMjudgesandICMBoardmembersfor their valuableandunflagging efforts; and

?the staff of the U.S. Military Academy,West Point, NY, for hosting the triage and final judgings.

Cautions

To the reader of research journals:

Usually a published paper has been presented to an audience, shown to colleagues, rewritten, checked by referees, revised, and edited by a journal editor. Each of the team papers here is the result of undergraduates working on

a problem over a weekend; allowing substantial revision by the authors could 164 The UMAP Journal 30.2 (2010)

give a false impression of accomplishment. So these papers are essentially au naturel. Light editing has taken place: minor errors have been corrected, wording has been altered for clarity or economy, style has been adjusted to that of The UMAP Journal, and the papers have been edited for length. Please

peruse these student efforts in that context.

To the potential ICM Advisor:

It might be overpowering to encounter such output from a weekend of

work by a small team of undergraduates, but these solution papers are highly atypical. A team that prepares and participates will have an enriching learning experience, independent of what any other team does.

Shedding Light on Marine Pollution 165

Shedding Light on Marine Pollution Brittany Harris

Chase Peaslee

Kyle Perkins

Carroll College

Helena, MT

Advisor: Philip Rose

Abstract

Massive amounts of plastic waste have been accumulating in the Great Pacific Garbage Gyre and are posing a threat to the marine environment. Since little is known about the degradation of plastics in this marine setting, we adopt the goal of modeling the photodegradation of a common plastic, polyethylene, in seawater. Plastic in the ocean is exposed to ultraviolet (UV) light fromthe sun, which causes photodegradation, a natural source of plastic decomposition.

We develop two models to describe the rate of photodegradation of polyethylene floating in seawater, a Low-Transmittance of Light Model (LTM) and

a High-Transmittance of Light Model (HTM). Using the constant rate of UV irradiance and the average bond dissociation energy of carbon-carbon single bonds (C–C), we calculate the mass lost per unit of time.

The results from our models are realistic. The HTM predicts that a rectangular prism of polyethylene 1 ×1 ×2 cm weighing 1.87 g will lose 1.27 g

of mass in one year; the LTM predicts that a hollow sphere with thickness 0.0315 cm, radius 5 cm, and weight 9.145 g, partially submerged in

lowtransmittance

water, will lose 0.190 g of mass in the first year. The design of

our models allows us to model other shapes, adjust the intensity of UV light, and realistically predict the photodegradation of polyethylene.

Introduction

The accumulation of plastic debris in our oceans is quickly coming to light as one of the most prevalent and devastating threats to the marine environment. The ―Great Pacific Ocean Garbage Patch‖ is one of many areas

of wind-current convergence where massive amounts of debris collect and stew. The ―garbage‖ is not primarily in the form of bottles and bags, TheUMAPJournal 31 (2) (2010) 165–174. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 166 The UMAP Journal 31.2 (2010)

but rather as tiny particles referred to as neustonic plastics. These neustonic

plastics are the products of degradation of post-consumer and industrial wastes and may pose great risk for marine life. The nature of the degradation

of plastics has thus become an important element in the study of this environmental catastrophe.

We focus specificallyon the photolytic degradation of polyethylene plastic accumulating in the gyre. We consider

?the UV radiation reaching the surface of the ocean;

?the energy required to break the bonds in polyethylene; and

?physical considerations concerning buoyancy, mass, and surface area of the plastic particles.

Description of the Problem

We consider the degradation of floating polyethylene fragments by photolytic

degradation. The fragments are considered to be hollow spheres

partially filled with seawater, to represent common post-consumer waste containers. The fragments are partially submerged in water with either

low or high transmittance of light. High-transmittance water can use the entire effective surface area of the fragment to model degradation, while for fragments in low-transmittance water only the portion of the fragment above water will be susceptible to photolytic degradation [Ivanhoff, Jerlov, andWaterman 1961].

Ultraviolet light is assumed to hit the fragment orthogonally to the plane of the ocean, thereby exposing a two-dimensional surface area of effective area c. We relate c to the radius r of the fragment; the mass m of the fragment depends on both. The goal is to model these relationships over time to describe the loss of mass experienced by a polyethylene fragment. Photolytic Degradation of Polyethylene Polyethylene is a polymer consisting of long chains of the monomer

ethylene [Carey and Sundberg 2007]. There are two types of bonds present in polyethylene: carbon-carbon single bonds (C–C) and carbon-hydrogen single bonds (C–H) [Leeming 1973]. Polyethylene has the structure ?(CH2?CH2)n?

where n is the number of monomers in the chain.

Photodegradation is a process by which chemical bonds are broken when struck by light [Carey and Sundberg 2007; Okabe 1978]. The light must carry enough energy to cleave a bond, which can be estimated using Shedding Light on Marine Pollution 167

the average bond dissociation energy [Leeming 1973]. The equation E = hc

λ

,

where h is Planck‘s constant and c is the speed of light, can be used to find the minimum wavelength λof light that carries enough energy to break the bond [Skoog, Holler, and Crouch 2007]. For example, the energy to cleave a C–C single bond is 5.778 ×10?19 kg ·m2/s2. Using h = 6.626 10?34 kg ×·m2/s and c = 3 ×108 m/s, we find λ= 344 nm, a wavelength in the ultraviolet.

Thus, when polyethylene is exposed to ultraviolet light (UV) with a

wavelength of 344 nm, C–C single bonds are cleaved and free radicals are

formed that react quickly with O2 to form peroxy radicals. Then either the peroxy radicals continue a chain reaction of radical formation or else two free radicals react to terminate the chain reaction [Carey and Sundberg 2007; McNaught and Wilkinson 2007; Trozzolo and Winslow 1967]. The pathway of free radical chain reactions and termination reactions can be seen in Figure 1.

Photo oxidative reaction mechanism:

R–H + UV ?→R·

R ·+O2 ?→R–O–O·

R–O–O ·+R ·H ?→R–O–O–H + R·

Photo oxidation termination reactions:

R ·+R·?→R–R

R–O–O ·+R·?→R–O–O–R

Figure 1. Reactions of peroxy radicals.

The cleavage of C–C single bonds breaks the polyethylene into fragments and the polyethylene loses mass. The rate of degradation can be

estimated by assuming that every time a C–C bond is cleaved by UV light, a monomer is removed from the original mass of polyethylene. The rate at which the C–C bonds can be cleaved depends on the amount of UV light emitted by the sun, which is 0.0005 watts/m2 = J/s·m2 [Karam 2005]. Since the energy to break a C–C bond is 5.778 ×10?19 J and there are Avogadro‘s number (6.022 ×1023) molecules in a mole, we can find via unit conversion the rate of photodegradation of polyethylene:

168 The UMAP Journal 31.2 (2010)

1 C–C bond

5.778 ×10?19 J ×

0.0005 J

1 s ·1 cm2 ×

1 mole polyethylene

6.022 ×1023 C–C bonds

×

28 g monomer polyethylene

1 mole polyethylene

=

4.02 ×10?8 g monomer polyethylene

s ·cm2 .

General Assumptions

?Since mechanical degradation due to torque on plastic is minimal due to the small size of plastic particles [Tipler 2004], and colliding plastic particles are rare due to low particle density [Moore, Lattin, and Zellers 2005], in our model we neglect mechanical degradation.

?Polyethylene particles float in seawater, since medium-density polyethylene‘s

density is 0.937 g/ml [Chevron Phillips Chemical Company n.d.] and average density of 35 ppt saline seawater at 15?C is 1.0255 g/ml. We neglect water currents.

?The source of UV light is a constant average at sea level in the Pacific Northwest [Karam 2005].

?Polyethylene in the model does not containUVstabilizers and is medium density.

?Polyethylene is composed of ethylene monomers and the average bond dissociation energy for C–C single bonds is used to predict the energy needed to cleave the C–C bonds [Leeming 1973].

?Only the portions of the plastic fragments that are perpendicular to the UV light are subject to photolytic degradation.

?Only the effective surface area above water can receive UV light. ?The photolytic cleavage of C–C bond in the model is a fast forward reaction (Krxn . 1) and the reverse reaction is very slow. Immediately

after the bond is cleaved, the free radical forms and is quenched by any of the termination reactions that also have a Krxnb . 1. We also assumed 100% quantum efficiency of these reactions.

High-Transmittance Model

This model considers the degradation of a square prism of polyethylene on a flat surface on land or in water with a very high transmittance of light. One of the faces of the prism faces directly perpendicular to the UV Shedding Light on Marine Pollution 169

light source. Let K1 the rate of degradation from the calculation on p. 168, 4.02 ×10?8 (g monomer polyethylene)/s·cm2. Then

Z y

Z x

Z t

K1 dt dx dy = K1txy,

due to the simple geometry. The result is a simple linear model of degradation

based on time and area.

Consider a square prism with the dimensions of 1 cm×1 cm×2 cm, with an area 1 cm×1 cm exposed to UV radiation. It has an initial mass of 1.87 g

[Chevron Phillips ChemicalCompanyn.d.]. After one year ofUVexposure, about two-thirds—1.27 g of polyethylene—is lost as a result of photolytic degradation.

Low-Transmittance Model

A primary factor in describing the amount of UV light that a fragment of plastic absorbs is the effective surface area perpendicular to direct sunlight.

Since the North Pacific Gyre is a collection of floating debris, we use Archimedes‘ principle to relate the buoyancy of a piece of plastic to its effective

surface area. For simplicity, we neglect the effect of air in the container on buoyancy. Archimedes‘ principle states that ―the buoyant force on a

submerged object is equal to the weight of the fluid that is displaced by that object‖ [Hodanbosi 1996]. In addition, since the plastic is in kinetic equilibrium

in the vertical direction, its buoyant force must be equal in magnitude to its weight:

Fbuoyant = Wplastic = Mplastic g = Mwater displaced g = Vplastic submerged dwater g,

whereM is mass,W is weight, V is volume, d is density, andg is acceleration due to gravity. Thus, we have

Mplastic = Vplastic submerged dwater,

whose right-hand side can be calculated from the triple integral

Z π

x

Z 2π

Z h

r?h

d ·ρ2 sin φ dρ dθ dφ,

where h is the thickness of the plastic and x is the angle from the zenith to the point on the sphere‘s surface where the sphere contacts the water level (see Figure 2). Setting this integral equal to the total mass of the plastic, we can find x. Trigonometry relates the radius r of the sphere and the angle x to the effective surface area c of the sphere exposed perpendicularly to UV rays, as indicated in Figure 2.

170 The UMAP Journal 31.2 (2010)

Figure 2. Geometry of a sphere at the ocean‘s surface.

As shown in Figure 2, the effective solar radius is

re = r cos

≥π

2 ?x

\

.

By subtracting the volumes of two concentric spheres withΔr = h, then

multiplying by the density l of the plastic, we get M =

Σμ

4

3 πr3

?

?

μ

4

3 π(r ?h)3

l.

We solve for r:

r =

πh2 ±

s

π2h4 ?πh

μ

4

3 πh3 ?

m

l

?

2πh

.

We define a constant C based on the relationship between the mass (in grams) of plastic and the total bond energies (in joules) within that mass, based on the molar mass and the average bond energy of polyethylene:

C ≡1 J ×

1 mole

348000 J ×

28 g

1 mole

= 8.046 ×10?5 g/J.

Ultraviolet light is the source of energy in this model. A true empirical value for the amount U (J/cm2·yr) would need to be measured on site. The Shedding Light on Marine Pollution 171

product UC has units of g/cm2·yr. To solve for a total change in grams over a specific time and area, we integrate the term with respect to time and then with respect to area:

Z t

Z 2π

Z re

UC ·r dr dθ dt = Δm = UCr2

eπt.

Subtracting from the initial mass, we have

Mfinal = m?UV Cr2

eπt.

Using the Low-Transmittance Model, consider a hollow sphere with

thickness 0.0315 cm, radius 5.00 cm, and initial mass 9.145 g. After one year of UV exposure, the loss in mass is 0.190 g of polyethylene. The rate

of degradation can be visualized in Figure 3.

Figure 3. Degradation of mass of polyethylene sphere over time.

Comparisons and Limitations

We develop two models to determine mass lost to photodegradation froma piece of polyethyleneplasticexposedtoUVlight.

TheHigh-Transmittance

Model models the polyethylene as a rectangular prism; the Low-

Transmittance Model models the exposed effective surface area of a hollow sphere of a particular thickness, partially submerged. Depending on the conditions of the water (density and transmittance) and the shape of the object, the models can be modified to describe photodegradation of polyethylene in many other shapes in high- or low- transmittance water. To increase the accuracy of our models, a few main points need additional research and refinement:

172 The UMAP Journal 31.2 (2010)

?The value U used for irradiance of UV light in the North Pacific Ocean needs to be verified.

?Mechanical degradation will also take place and should be included. ?The models do not describe the fact that particles tend to converge on a similar size around 3–5 mm [Yamashita and Tanimura 2007].

?Many polyethylene products contain UV stabilizers that increase the longevity of the plasticby inhibiting the free-radical chain reaction [Carey and Sundberg 2007].

?Polyethylene can vary in density. Our model uses medium-density polyethylene

(MDPE).

?Plastics are not just on the ocean surface but also at depths up to 100 ft. ?Polyethylene, although very common, is not the only plastic in the North Pacific Gyre.

Discussion of Impacts

Our models describe the rate at which UV light breaks down polyethylene. The process is slow, and there is inconclusive evidence as to whether plastics ever degrade entirely in the Gyre. Plastics are thus a prevalent long-term environmental antagonist. Possible ecologic effects of the accumulation

of massive amounts of plastic in the Pacific Ocean Gyre include

ingestion of plastic particles by marine life, the disturbance of the transmittance

of light below the surface of the water (which may affect many

organisms‘ ability to synthesize energy from photosynthesis), and the distribution

of hydrophobic pollutants. Our model relates to the ingestion of

plastic particles by marine life because it predicts the mass of fragments at a given time and marine organisms may confuse plastic fragments that are similar in size to their normal food source.

Contributing to the growing problem of plastic pollution in the ocean

is the lack of governmental regulation on pollution by cruise ships. During a one-week trip, a typical cruise ship produces 50 tons of garbage.

Regulations are tricky though, because international waters do not have well-defined environmental authority structures, and monitoring is minimal

[State Environmental Resource Center 2010]. Stronger regulations and monitoring systems are required to decrease the impact of pollution by cruise ships.

Land-based sources contributeup to 80% of marine debris, 65% of which is from post-consumer plastics that were improperly disposed of [Algalita Marine Research Foundation 2009]. This means that the plastics are littered,

not just that they are not recycled. Many states have laws against Shedding Light on Marine Pollution 173

littering, but monitoring efforts need to be improved. Education and monitoring

programs may be expensive, but the cost would likely be small when compared to the potential for environmental protection.

Conclusion

We propose two realistic models for the photodegradation of polyethylene. The first model is for a solid chunk of polyethylene either on land or in

water with 100% transmittance of light. The second model is more complex and considers a partially submerged hollow sphere of polyethylene that is degraded only over the effective surface area. Our models can accurately describe degradation of partially degraded or intact plastic products, since the initial physical properties (size, mass, etc.) of polyethylene can be varied

in both models. The ease of customization and thorough consideration of realistic variables make our models suitable for use.

References

Algalita Marine Research Foundation. 2009. Frequently asked questions (FAQs). http://algalita.org/AlgalitaFAQs.htm .

Anthoni, J. Floor. 2006. The chemical composition of seawater. http: //.nz/oceano/seawater.htm .

Carey, Francis A., and Richard J. Sundberg. 2007. Advanced Organic Chemistry:

Part A: Structure and Mechanisms. 5th ed. New York: Springer.

Chevron Phillips Chemical Company. n.d. Blown film. http://www. cpchem.com/bl/polyethylene/en-us/Pages/BlownFilm.aspx .

Hodanbosi, Carol. 1996. Buoyancy: Archimedes Principle.

http://www.grc.nasa.gov/WWW/K-12/WindTunnel/Activities/

buoy_Archimedes.html .

Ivanhoff, Alexandre, Nils Jerlov, and Talbot H. Waterman. 1961. A comparative

study of irradiance, beam transmittance and scattering in the

sea near Bermuda. Limnology and Oceanography 2(2): 129–148.

Karam, Andrew. 2005. Re: What percent age [sic] of natural sunlight is UV rays? /posts/archives/2005-06/

1119964750.En.r.html .

Leeming,William B.H. 1973. Thermal and photolytic degradation of polypropylene.

Thesis, University of Glasgow. http://theses.gla.ac.

uk/1509/01/1973leemingphd.pdf .

McNaught, A.D., and A. Wilkinson. 1997. Compendium of Chemical Terminology.

2nd ed. New York: Oxford University Press.

174 The UMAP Journal 31.2 (2010)

Moore, C.J., S.L.Moore, M.K. Leecaster, and S.B.Weisberg. 2001. Acomparison

of pLastic and plankton in the North Pacific Central Gyre. Marine Pollution Bulletin 42: 1297–1300.

Moore, C.J., G.L. Lattin, and A.F. Zellers. 2005. Density of plastic particles found in zooplankton trawls from coastal waters of California

to the North Pacific Central Gyre. /pdf/

Density%20of%20Particles%20spellchkd11-05.pdf .

Okabe, Hideo. 1978. Photochemistry of Small Molecules. New York: Wiley- Interscience.

Skoog, Douglas A., F. James Holler, and Stanley R. Crouch. 2007. Principles

of Instrumental Analysis. 6th ed. Florence, KY: Thompson Brooks/Cole. State Environmental Resource Center. 2004. Issue: Cruise ship pollution. /cruiseShipPollution.html .

Tipler, Paul Allen. 2004. Physics for Scientists and Engineers. New York: W.H. Freeman.

Trozzolo, A.M., and F.H. Winslow. 1967. A mechanism for the oxidative photodegradation of polyethylene. Macromolecules 1: 98–100.

Wade, L.G. Organic Chemistry. 7th ed. Upper Saddle River, NJ: Pearson Prentice Hall.

Yamashita, Rei, andAtsushiTanimura. 2007. Floating plastic in theKuroshio Current area, western North Pacific Ocean. Marine Pollution Bulletin 54(4): 485–488.

Team members Brittany Harris, Kyle Perkins, and Chase Peaslee. Author’s Commentary 175

Author’s Commentary:

The Marine Pollution Problem

Miriam C. Goldstein

Integrative Oceanography Division

Scripps Institution of Oceanography

University of California, San Diego

9500 Gilman Drive, Mailbox 0208

La Jolla, CA 92093–0208

mgoldstein@ucsd.edu

Introduction

Lightweight, inexpensive, durable, and infinitely variable, plastic defines

the modern age. However, the very qualities that make plastic indispensable make it an environmental problem.

Today, plastic waste is found throughout the world‘s oceans, from the coast to the depths to the center of the open sea far from land. The best-known accumulation of trash is the ―Great Pacific Garbage Patch,‖ located in the North

Pacific Central Gyre (NPCG), a vast swathe of ocean that stretches between the

west coast of North America and the east coast of Asia.

Borderedbyfour major currents, theNPCGslowly rotates clockwise, pulling water in towards the center. Plastic debris from North America and Asia that does not sink or degrade becomes trapped in the NPCG. While larger pieces of plastic such as fishing nets and disposable drink bottles are found in the NPCG, most of the plastic debris is small. This is because as plastic items are exposed to ultraviolet light, they become brittle and are broken into smaller and smaller pieces by the movement of the ocean. This process is known as photodegradation.

The environmental impacts of small pieces of plastic debris are poorly understood.

Larger pieces of debris, such as lost fishing gear, can entangle and

drown oceanic animals such as seals and turtles. Seabirds and turtles eat plastic

debris, and turtle death has been linked to intestinal blockage fromplastic bags.

However, effects on the organisms at the base of the food chain, such as phytoplankton,

zooplankton, and small fishes, remain less studied but may be more

TheUMAP Journal 31 (2) (2010) 175–177. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 176 The UMAP Journal 31.2 (2010)

significant due to the high proportion of plastic debris that is less than 3 mm in diameter. Small particles of plastic are readily ingested by filter-feeding and deposit-feeding invertebrates, and plastic resin pellets accumulate high levels of persistent organic pollutants such as PCBs and DDT. Plastic debris also serves as a ―raft‖ for benthic invertebrates such as barnacles, and has already been responsible for at least one exotic species introduction in the Atlantic. The ―Great Pacific Garbage Patch‖ has captured the public imagination, leading to a great deal of coverage in the popular media. While detectable amounts of plastic debris were documented in the NPCG as early as 1972, the public awareness of this issue is due in large part to Capt. Charles Moore and the nonprofit organization he founded to combat marine debris, the Algalita Marine Research Foundation. However, relatively little is known about the extent and environmental effects of the plastic debris. Since a robust scientific understanding of the problem is necessary to seeking a solution, the ―Great Pacific Garbage Patch‖ was the topic for this year‘s problem in the

Interdisciplinary

Contest in Modeling (ICM)!R .

Formulation and Intent of the Problem The goal of this year‘s ICM problem was for student teams to model one aspect of the marine debris issue in the NPCG. Because the issue

encompasses

physical oceanography, ecology, and waste management, there were many potential issues to choose from. Teams were asked to focus on one critical aspect of the problem of oceanic marine debris, and to model the important behavior and phenomena. The end result was to be in the form of a 10-page report to the leader of an expedition setting off to study marine debris. Suggested tasks included:

?Create a monitoring plan, with the option of including other oceanic gyres such as the North Atlantic Gyre and South Pacific Gyre.

?Characterize the extent, distribution, and density of debris.

?Describe the photodegradation of debris.

?Model the impact of banning polystyrene takeout containers.

?Pursue any relevant topic of the team‘s choosing that included modeling. Models were evaluated based on the team‘s understanding of the nature of the problem, their use of realistic parameters, and their approach to describing either the existing problem or a proposed solution.

This year‘s ICM problem is based on ongoing research by a variety of organizations

and scientists, particularly the Algalita Marine Research Foundation, the Sea Education Association, Project Kaisei, and Scripps Institution of

Oceanography. Most work has focused on understanding the abundance and distribution of plastic particles in the NPCG. Future work will focus on the impacts and mitigation of marine debris.

Author’s Commentary 177

About the Author

Miriam Goldstein is a fourth-year Ph.D. student

in Biological Oceanography at the Scripps

Institution of Oceanography at the University of

California San Diego, CA. For her dissertation

work, she is studying the effect of plastic debris

on zooplankton communities and invasive

species transport. She was the principal investigator

on the 20-day Scripps Environmental Accumulation

of Plastic Expedition(SEAPLEX)that

investigated plastic debris in the North Pacific

Gyre in August 2009. Miriam holds an M.S. in

Marine Biology from Scripps and a B.S. in Biology

from Brown University. She is originally

from Manchester, NH.

178 The UMAP Journal 31.2 (2010)

Judges’ Commentary 179

Judges’ Commentary:

The Outstanding Marine Pollution Papers

Rodney Sturdivant

Dept. of Mathematical Sciences

U.S. Military Academy

West Point, NY

Rodney.Sturdivant@usma.edu

Introduction

The Interdisciplinary Contest in Modeling (ICM)!R is an opportunity for

teams of students to tackle challenging real-world problems that require a wide breadth of understanding in multiple academic subjects. This year‘s problem focused on the recently much publicized ―Great Pacific Ocean Garbage Patch.‖

Scientific expeditions into the North Pacific Central Gyre (a convergence zone where debris is accumulating) have led to a number of interesting scientific and

technical problems. (Hereafter we refer to it simply as ―the Gyre.‖)

Eight judges gathered to select the most successful entries of this challenging competition out of an impressive set of submissions.

The Problem

The primary goal of this year‘s ICM was to model and analyze one issue

associated with the debris problem. Specifically, teams were asked to address several elements with their model:

1. Determine the problem‘s potential effect on marine ecology.

2. Address government policies and practices that should be implemented to ameliorate the negative effects.

3. Consider needs for future scientific research.

4. Consider the economic aspects of the problem.

TheUMAP Journal 31 (2) (2010) 179–184. !c Copyright 2010 byCOMAP, Inc. All rights reserved. Permission to make digital or hard copies of part or all of this work for personal or classroom use is granted without fee provided that copies are not made or distributed for profit or commercial advantage and that copies bear this notice. Abstracting with credit is permitted, but copyrights for components of this work owned by others than COMAP must be honored. To copy otherwise, to republish, to post on servers, or to redistribute to lists requires prior permission from COMAP. 180 The UMAP Journal 31.2 (2010)

Several examples of issues that the teams might consider were also provided. For the first time, the ICM problem submissions were limited to a

maximum length of 10 pages.

Overall, the judges were impressed both by the strength of many of the

submissions and by the variety of issues they chose to model. In many cases, very different modeling approaches were used to address the same issue; as a result, this year‘s problem led to the greatest variety in submissions to the ICM in memory.

Judges’ Criteria

The framework used to evaluate submissions is described below, and it

remained very similar to the criteria used in 2009. However, the 10-page limit for the submissions had an impact on the importance of the final criterion concerning communication. Teams that dramatically exceeded the limit were not considered for the Outstanding paper category.

Executive Summary

It was important that a team succinctly and clearly explain the highlights of its submission. The executive summary needed to include the issue that the team chose to address and the modeling approach(es) used for analysis. Further, the summary needed to answer the most pressing questions posed in the problem statement, namely, the effect on the marine ecology, economic aspects of the issue, and how to ameliorate the problem. Truly outstanding papers were those that communicated their approach and recommendations in well-connected and concise prose.

Domain Knowledge and Science

The problem this year was particularly challenging for students in terms of the science. To address the requirements effectively, teams needed first to establish an ecological frame of reference. Many teams were able to do this reasonably well; teams that excelled clearly did a great deal of research. Often, what distinguished the top teams was the ability not just to describe the garbage patch in a single section of the paper, but also to integrate this domain knowledge throughout the modeling process.

A second important facet of the problem was the ability to understand

economic issues associated with the chosen problem. Many teams created reasonable

models but unfortunately never tied them to the economic discussion. Judges’ Commentary 181

Modeling and Assumptions

For teams that chose to focus on describing and understanding the distribution of plastic in the Gyre, simulation was a popular approach to the problem. Differential equations were probably the most prevalent models used (in a wide variety of ways). Often, the models appeared appropriate but lacked any discussion of important assumptions. Additionally, some papers lacked a reasonable discussion of model development. Finally, the very best papers not only formulated the models well but also were able to use the models to produce

meaningful results to address the problem and to make recommendations. Solution/Recommendation

Perhaps the most distinct difference between the best papers and others was the ability to utilize the team‘s models to develop or propose an actual solution to the problem. For example, a team might effectively model the distribution of

plastic in theGyre in one section of the paper. Acompletelyindependentsection would then provide recommendations for remediating the plastic problem but without ever making use of the model or the model results.

Analysis/Reflection

Successful papers utilized the models developed in early sections of the

paper to draw conclusions about the important issues in addressing problems with the garbage patch and addressed how assumptions made in the model could impact the solution and recommendation. In the best papers, trade-offs were discussed and—in truly exceptional cases—some sensitivity analysis was

conducted to identify potential issues with the solutions presented.

Communication

The challenges of the modeling in this problem and the page limit may have contributed to the difficulty that many teams had in clearly explaining their solutions. Papers that were clearly exposited distinguished themselves significantly, emphasizing that it is not only good science that is important, but

also the presentation of the ideas. In some cases, teams spent all their space describing the modeling and never presented important results, conclusions, or recommendations. On the other hand, some teams never really explained their models, making it difficult to judge the validity of their results. Balancing the need to present enough work to fully answer the question, while keeping to the 10-page limit, was clearly a challenge in this year‘s contest.

182 The UMAP Journal 31.2 (2010)

Discussion of the Outstanding Papers The judges were most impressed by papers that offered unique and innovative ideas. Three of the four Outstanding papers this year took very novel

approaches to the problem and issues. The fourth paper was representative of what many teams opted to do but was more clearly articulated and the modeling more complete than others attempting the same approach. ?The Beijing Jiaotong University submission ―A New Method for Pollution Abatement: Different Solutions to Different Types‖ was unique in looking at the pollution problem from a risk-analysis perspective. Using multiattribute decision theory, this team developed a model to rank the types of

debris in the Gyre by their level of ―risk.‖ The modeling was complete and well explained. The team also then used the results of the model to propose a strategy for reducing the debris problem. The judges were a bit troubled by the conclusions of the paper—considering types of debris as significantly differentmaynot be realistic—but the results followed fromthe assumptions in the Moore et al. [2001] paper provided with the problem statement.

?The paper from Lawrence University, ―Size-Classified Plastic Concentration in the Ocean,‖ was perhaps the most clearly written and thorough among the Outstanding papers. The team developed a model to classify the plastics in the Gyre. Their models looked at many factors, physical and chemical, to determine size and concentration of the debris. In addition to the very thoroughly

explained modeling efforts, the paper ends with sections discussing

some of the limitations of the model and then some very specific conclusions and recommendations that stem directly from the model itself.

?The Hangzhou Dianzi University submission, ―Quantitative Marine Debris Impacts and Evaluation of Ocean System,‖ became known among the judges as the ―monk seal‖ paper. This team took a unique approach to the problem by studying the impacts of ocean debris on a single species, the Hawaiian monk seal. A ―grey model‖ and time-series approach was utilized to

consider trends for the monk seal, and then an analytical hierarchy process (AHP) used to try to quantify impacts of debris. The paper was not

the strongest in terms of how well the team explained and presented their results, but the clever approach to the problem appealed to the judges. ?The final Outstanding paper, ―Shedding Light on Marine Pollution‖ by the team from Carroll College, considered the specific issue of photodegradation of polyethylene floating in seawater. The team developed models for this process and very clearly articulated their approach and assumptions. This paper was among the best at presenting the modeling efforts and also noteworthy for the science (namely, chemistry) utilized in the process. The judges would have liked to see a bit more in the conclusions to explain the importance of the modeling results and ties to policy, but they were very impressed by the focus and clarity of this paper.

Judges’ Commentary 183

Conclusion and Recommendations for Future Participants

The judges really enjoyed reading the submissions for this year‘s ICM contest. All teams deserve congratulations for the tremendous work done in a

very short period of time and on a very difficult problem. The judging was, as a result, both pleasurable and challenging.

One issue worthy of mention that arises each year is that of proper scholarship in utilizing other sources in writing a paper. In researching the science for these complicated problems, teams naturally use information and ideas taken from a variety of resources. This is acceptable as long as those ideas are clearly

documented in the paper. Copying the exact words from other papers should be minimized; but, if done, the words need to be placed in quotation marks, so that it is clear that it is not original to the authors.

Several key points from this year‘s contest judging emerged in determining the very best submissions. These are thoughts that may be useful to future ICM

competitors.

?Many teams failed to select a single issue to model and analyze, instead trying

to address all of the ideas for issues proposed in the problem statement. In some cases, these teams appeared to have done a remarkable amount of excellent modeling. However, it was simply impossible for them to present all this work in such a short report or to do justice to such a wide array of problems in such a short time period. The teams that were most successful clearly shaped the problem that they would address. When presented with a problem with a very large scope, narrowing the focus is critical.

?Judges were impressed with those who took a unique perspective on the problem. That could be either a different modeling approach (perhaps using a particular science, such as chemistry) or considering a different aspect of the problem (one example was a team that looked at how the plastic gets into the ocean). Original thought, as long as it was grounded in solid research, was cherished.

?Finally, a well-written and integrated report that reads well from start to finish is critical. The sections of the report should follow naturally and

not appear as completely separate sections or ideas. The conclusions and recommendations, in particular, should be clearly tied to the modeling work presented.

Reference

Moore, C.J., S.L. Moore, M.K. Leecaster, and S.B.Weisberg. 2001.

Acomparison

of plastic and plankton in the North Pacific central gyre. Marine Pollution Bulletin 42: 1297–1300.

184 The UMAP Journal 31.2 (2010)

About the Author

Rod Sturdivant is an Associate Professor at the U.S. Military

Academy inWest Point, NY. He earned a Ph.D. in biostatistics

at the University of Massachusetts–Amherst and is

currently program director for the probability and statistics

course atWest Point. He is also founder and director of the

Center for Data Analysis and Statistics within the Dept. of Mathematical Sciences. His research interests are largely in applied statistics with an emphasis on hierarchical logistic regression models.

更多类似范文
┣ 一小时的故事读后感 2800字
┣ 了不起的盖茨比读后感言 6700字
┣ 英语读译读后感作业 9300字
┣ 初二英语作文:读后感 600字
┣ 更多the story of an hour 读后感
┗ 搜索类似范文

更多相关推荐:
Of A Doll(1)英文读后感4600字

OfADollsHouseAbrokenmirrorjoinedtogetherIcontendthatIdbettercompareNoraandHelmersmarriagetoabrokenmirrorwhichcannot...

《英语短篇小说选读》教学大纲800字

英语短篇小说选读教学大纲作为一门选修课英语短篇小说选读主要面向英语专业本专科学生同时兼顾非英语专业各科英语成绩优异并对英语文学感兴趣的学生本课程旨在通过引导学生仔细研读英语短篇小说欣赏其精美的语言和深邃的思想提...

专栏推荐
大家在关注

地图地图CC